manualshive.com logo in svg

SPACEMAKER RGB108FGEU, Руководство пользователя и инструкции по сборке

Поделиться
Скачать
SPACEMAKER RGB108FGEU Скачать руководство пользователя страница 27

 3719     Door Handle Brace (2)

 10472  Right and Left Doors (2)

 10497  Horizontal Door Brace (4) 

 6301    Vertical Door Brace (2)

 Parts Needed For 

Door Assembly

Step 17

The steps on this page tell how to 
assemble the right door. You will per-
form exactly the same procedures for 
the left door. Each bolt and screw in 
the door requires a washer. Proceed 
as follows:

1 

Attach the door handle brace 

and  handle  to the door  with 1 bolt 
as shown. Don't tighten the bolt yet.

2 

Swing the door handle brace up 

to the hole on the center of the door 
and insert a screw.

3 

Hold the vertical door brace 

against the center of the inside sur-
face of the door and turn the screw 
to hold the vertical door brace and 
door handle brace in place.  Fasten 
to door above and below center 
connection using 2 screws.

4 

Insert a second bolt in the door 

handle and tighten both bolts.

5 

Put a horizontal door brace onto 

the top edge and bottom edge and 
fasten with 1 bolt in the center.

6 

Attach the lower door guides and 

bolts as shown.

7 

Repeat steps 1 through 6 for the 

left door.

(4)

(6)

(12)

10472

 

 Right Door

66382

66382  

10497

66045

3719

10497

10497

66382

END VIEW

SHOWING:

Horizontal

Door Brace

Door

Washer

Guide

6301

6301

3719

10472 

  

Left Door

66045

66045

3719

10497

6301

66382

66382

STEP

1

STEP

2

STEP

3

STEP

4

STEP

5

STEP

6

28

JC28

Step 18

A31ctr

 Parts Needed For 

Door Installation & Adjustment

 Right Door Assembly (1)

 Left Door Assembly (1)

Keep this Owner's Manual and Assembly Instructions for future reference.

   

1 

From inside the building, put the 

bottom of the right door assembly 

(on your left when you are inside the 

building) behind door jamb into the 

front frame track.

2 

Position the top of the door so that 

the holes in the door line up with the 

holes in the door slides.

3 

Fasten the door to the door slides 

using two #10Bx1/2" (13 mm) screws 

per door slide.

NOTE

The holes in the door slides allow 

you to adjust the doors. Place the 

door in the middle holes.

4 

Repeat steps 1 through 3 for the 

left door.

Horizontal Door Brace

STEP

1

Gable

#10Bx1/2" (13 mm)

      Screw

Door Slide

Adjustment Holes

Adjustment Holes Allow

Doors to Meet Evenly

Along Their Length

Right Door

Left Door

Front Floor Frame Assembly

Door Track

Door Slide

D

oor

(8)

STEP

2

STEP

3

STEP

4

29

Содержание RGB108FGEU
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды