manualshive.com logo in svg

SPACEMAKER RGB108FGEU, Руководство пользователя и инструкции по сборке

Поделиться
Скачать
SPACEMAKER RGB108FGEU Скачать руководство пользователя страница 18

Step 8

 Parts Needed For 

Wall Panels

 5210 Wall Panel (4)

 6521 Wall Panel (4)

 11234   Gusset Strap (2)

 67521   Edge Trim (1)

The wall panels come in two widths. 

Each wall panel has a crimped rib 

on one side. The crimped rib should 

go under the rib of the panel that 

follows it.

1 

Locate all of the wall panels and 

set each one alongside the building.

2 

Be sure that you have the correct 

panels in each position. Do this by 

overlapping the panels and determin-

ing if the holes line up with the holes 

in the frame.

3 

Fasten the wall panels at the top 

and bottom with screws.

4 

Fasten the center of each panel to 

the wall channel with screws. Fasten 

overlapping ribs as before.

5 

When you have attached all wall 

panels in the correct positions, the 

building will look like this.

STEP

1

5210

STEP

2

5210

STEP

4

Bolt and nut

does not go thru

wall channel

at overlap

STEP

3

Crimped Rib

Underneath

STEP

5

Use bolts and nuts thru wall

angle overlaps at the top of

panel at sides and rear.

6521

5210

5210

6521

Detail Showing

Center of Panel Screwed

to Wall Channel

6521 6521

Panels rest on

frame as shown

(112)

(17)

19

JC19

(4)

11234

11 1/2”

29,2 cm

67521

X2

11234

67521

Содержание RGB108FGEU
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды