manualshive.com logo in svg

SPACEMAKER RGB108FGEU, Руководство пользователя и инструкции по сборке

Поделиться
Скачать
SPACEMAKER RGB108FGEU Скачать руководство пользователя страница 16

1 

Position a corner panel at the 

corner of the fl oor frame as shown. 

The widest part of each corner panel 

must be placed along the side of the 

building for all four corners. Fasten 

the corner panel to the fl oor frame 

with one screw.

Support the corner panel with a step 

ladder until a wall panel is attached.

2 

Attach the front wall panels to 

the front corner panels, as shown. 

A small gap will exist between front 

wall panel and ramp.

3 

Attach the wall panels to the rear 

corner panels, as shown.

NOTE

Be careful to install the correct 

panel in each position as shown

 6521 Wall Panel (2)

 9375 Front Wall Panel (2)

 9162 Corner Panel (4)

Step 6

 Parts Needed For 

Corners

NOTE

The remainder of the building assembly 

requires many hours and more than one 

person. Do not continue beyond this 

point if you do not have enough time to 

complete the assembly today. A partially 

assembled building can be severely 

damaged by light winds.

Each screw and bolt in the wall re-

quires a washer.

4 

Double-check the part numbers of 

the wall panels, before proceeding.

 The fl oor frame must  be  square                                    

 and level or holes will not align.

STEP

1

6521

9375

9375

9162

9162

REAR

FRONT

9375

Panels rest on

frame as shown

9162

SIDE

TOP VIEW

Narrow

Side

9162

6521

Wide Side

STEP

3

STEP

2

STEP

4

9162

9162

9375

6521

6521

9162

Washer

Crimped Rib

Underneath

9162

SIDE

(26)

(4)

CORRECT

INCORRECT

17

JC17

Содержание RGB108FGEU
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды