Space-Ray SRB40CRE-B2 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 30

Space-Ray SRB40CRE-B2 Скачать руководство пользователя страница 5

Form 43539178

Oct 2019

4

5. Flip the Emitter/Canopy Assembly over. Secure the Burner Base to the Burner Cap (which is

attached to the Emitter Assembly) and secure it in place using three (3) #10-24 hex locknuts
from the Fastener Kit. NOTE: Make sure that the two (2) holes located on the Burner Base
are facing the two (2) holes in the edge of the Canopy. See Figure 2.

6. Attach the Label Holder Plate and Manifold Support Bracket Assembly to the rim of the

canopy using two (2) ¼-20 screws, nuts and washers from the Fastener Kit. See Figure 3.
NOTE: DO NOT COMPLETELY TIGHTEN FASTENERS AT THIS STAGE YET.

7. Attach the Control Arm Assembly to the Manifold Support Bracket Assembly as shown in

Figure 3 using the V-clamp and the two (2) #10-24 screws pre-attached to the bracket. Slip
the keyway slots of the V-clamp over the screw heads.

NOTE: Adjust the Control Arm so that the V-clamp is butt against the tube fitting located at
the bottom of the gas valve. Tighten the screws.

NATURAL GAS MODELS ONLY. Slide the combustion air ring over the burner assembly before
attaching the Control Arm Assembly. Align the slot with the gas control arm tube.

8. Adjust the Control Arm so that the Orifice Fitting aligns with its connection point of the main

burner.

FIGURE 2

FIGURE 3

FIGURE 3

«
...
3
4
5
6
7
...
»

Содержание SRB40CRE-B2































Отзывы:

Нет отзывов