Space-Ray SRB40CRE-B2 Скачать руководство пользователя страница 1

 

 

 

Form 43539178 

 

 

 Oct 2019 


 

RADIANT GAS BROODER 

 

MODELS

:

  

 SRB40CRE (-2,-4, -9) with PILOT IGNITION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OWNER/INSTALLER:    For  your  safety  this  manual  must  be  carefully  read  before  installing,  operating  or 
servicing this brooder.  This brooder is intended for use with either Natural Gas or Propane Gas and must be 
installed  in  accordance  with  the  relevant  provisions  of  any  National  Gas  Safety  (Installation  and  Use) 
Regulations.    Due  account  should  also  be  taken  of  any  obligations  arising  from  any  National  Health  and 
Safety  at  Work  Regulations,  National  and  Local  Building  Regulations  and  National  Electrical  Wiring 
Regulations.  The appliance must be installed, and where necessary, converted for use on other gases, by a 
qualified installer. 

 

WARNING:  Improper installation, adjustment, alteration, service or maintenance can cause injury, property 

damage  or  death.    Refer  to  this  manual.    For  assistance  or  additional  information,  consult  a  qualified 
installer, service agency or the gas supplier.  

 

INSPECT all combustion air openings into the building and, if necessary, clear as they become blocked by 
litter, dust, feathers or other matter. 

 

INSPECT and clean the brooder filters on a regular basis to allow proper brooder operation. 

 

 

 

FOR YOUR SAFETY: EXHAUST FANS MUST be operating on an appropriate cycle when brooders are operating 
to avoid a high concentration of carbon monoxide.  When used without fresh air, this brooder may give off 
carbon monoxide, an odourless and poisonous gas.  CARBON MONOXIDE POISONING MAY LEAD TO DEATH.  
Early  signs  of  carbon  monoxide  poisoning  resemble  the  flu  with  headaches,  dizziness  and  nausea.    If  you 
experience these signs, GET FRESH AIR IMMEDIATELY!  Have the brooders serviced as soon as possible and 
check the ventilation in the house.   

 

 

 

These brooders are designed for agricultural applications and may operate with the use of either Natural Gas 
or  Liquid  Propane  (LP)  Gas.    Check  the  brooder’s  nameplate  to  determine  the  correct  gas  type  before 
proceeding with installation. 

 

 

 

 

 

IF YOU SMELL GAS: 

 

!

  DO NOT try to light any appliance. 

!

  DO NOT touch any electrical switch; do not use any 

telephone in your building. 

!

  IMMEDIATELY  call  your  gas  supplier  from  a  neighbour's 

telephone.    Follow  the  gas  supplier's  instructions.    If  you 
cannot reach your gas supplier, call the fire department. 

 

 

 

 

DO NOT store or use petroleum or 
other flammable vapours and liquids 
in the vicinity of this or any other 
appliance. 
 

SAVE THIS MANUAL 

FOR FUTURE REFERENCE.

 

 

 

INSTALLATION 

AND OPERATION 

INSTRUCTIONS 

 

FOR YOUR SAFETY 

Содержание SRB40CRE-B2































Отзывы: