Sovema FC-2 180 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 39

Sovema FC-2 180 Скачать руководство пользователя страница 26

OPERATION & MAINTENANCE MANUAL

page 24 Release 2017

MAINTENANCE

The efficiency and lifetime of this machine strongly depend on the observance of its
maintenance schedule. The schedule reported below is subject to change since it refers
to a normal usage and does not take into consideration heavier working conditions which
require a more frequent maintenance.

Disengage the PTO shaft before proceeding with
maintenance.

EVERY 10 WORKING HOURS

•

Check for loose bolts that fix the knives to the rotor. Tighten as needed.

•

Grease the PTO shaft components.

•

Clean the end of PTO shaft with non toxic/non inflammable detergent.

•

Make sure that PTO shaft protection shields are in place and in good condition.

•

Grease lateral supports of the rotor. Before greasing, clean the grease nipple correctly

for better lubrication. The lateral support of the right is at sight, the left one is covered
by the cover itself. For being able to grease this last one, you will find a hole in the
back part of the cover. Use lithium type grease NLGI2.

•

Clean the mower from residues.

«
...
24
25
26
27
28
...
»

Содержание FC-2 180








































Отзывы:

Нет отзывов