Southworth DANDY LIFT страница 11 Скачать руководство пользователя

Страница: 11 / 65

NEW STYLE DANDY LIFT OWNER'S MANUAL

WARNING:

Floor lock (parking brake) is fixed to prevent shoe from falling off during shipment. Do

not actuate as is. The following adjustments must be made as soon as the unit is as

sembled.

2. Adjustment of the show on the parking brake

• Adjustment work must be done on flat surface.

•

Step on lock lever until it clicks actuating the brake.

• Screw shoe down by rotating it in a clockwise direction so that it touches the floor.

•

Step on release lever to release the brake. Then rotate the shoe clockwise an additional

two turns to provide firm contact with the floor.

NOTE: By doing the above adjustments, shoe will compress by 1/8", assuring firm contact

with floor. If perfect braking is not achieved, repeat above adjustment.

Required pushing force for lock lever will increase, but braking effect will increase.

CAUTION:

Make sure floor lock is set during lifting or parking

INSPECTION AND MAINTENANCE

UD Dandy Lifts do not require special maintenance, other than lubrication and periodic in-

spection. Inspection and maintenance should be made in accordance with the following

procedure for smooth and efficient operation.

CAUTION:

During lubrication, inspection and maintenance the platform must be empty.

WARNING:

If the platform needs to be raised for access to lubrication points, the unit should be

laid over on its side. Do not put your hands into a raised lift.

NOTE: The following are recommended as support and must be fixed to the frame using

adhesive tape. Supports of the following size are recommended:

Width (in.)

Length (in.)

UDL-150

3/4 x 3/4

UDL-250

3/4 x 1-1/2

UDA-350W

3/4 x 1-1/2

UDA-500

3/4 x 1-1/2

UDA-800

3/4 x 1-1/2

Содержание DANDY LIFT


































































Результаты поиска

Содержание DANDY LIFT

Отзывы:

Похожие инструкции для DANDY LIFT

Бренды по названию

Популярные бренды

Southworth DANDY LIFT, Руководство пользователя

Результаты поиска

Содержание DANDY LIFT

Отзывы:

Похожие инструкции для DANDY LIFT

Бренды по названию

Популярные бренды