Southworth DANDY LIFT страница 12 Скачать руководство пользователя

Страница: 12 / 65

NEW STYLE DANDY LIFT OWNER'S MANUAL

A. Lubrication

Lubrication must be made in accordance with the following table:

Part

Lubrication Material

Fig. & Item No. To be referred

Rail (Frame)

Grease

N1-3*(S-3)

Roller (of Jack Lever)

Grease (Grease

Nipple)

N1-9-12 (S-9-12)

Hinge on Scissor

Machine Oil

N1-2-1 (S-2-1-1)

Stay

Machine Oil

N1-2-4 (S-2-4)

Lifting-up Box (moving part)

Machine Oil

N1-2-1-2 (S-2-1-2) N1-2-3

Parking Lock

Machine Oil

N1-7* (S-7)

Lowering Lever (moving part) Machine Oil

N1-8* (S-8)

Jack Pedal

Grease, One (1)

(Grease Nipple)

N1-9-4 (S-9-2)

Other Contacting and Sliding

Area

Grease/Machine Oil

Jack Oil

EP-32 or Equivalent

*( ) Is to be applied to UDL-150 Only

B. Inspection and Maintenance

Prior to use of the unit, check for any damage, deformation or cracks on the body.

NOTE: During inspection, the platform must be empty.

Remove foreign substance on scissors guide from the frame and rail.

•

Check lifting performance of the platform in accordance with provision of operation.

•

Check stopping performance at any desire height.

•

Check lowering speed and smooth action of the lowering lever.

C. Adjustment

1. Malfunctioning up/down of the platform.

If the platform does not lift up or hold in any position even while jack is pumped.

•

Air is in the jack unit

To bleed jack unit: Pump for three seconds and repeat a few times, then keep the unit

as is for about ten minutes. If air bubbles are not purged yet, repeat above adjustment

once more.

•

Jack valve does not close perfectly

Valve on jack will not be closed perfectly. In this case, adjustment is required in accor-

dance with the procedure on the next page:

Содержание DANDY LIFT


































































Результаты поиска

Содержание DANDY LIFT

Отзывы:

Похожие инструкции для DANDY LIFT

Бренды по названию

Популярные бренды

Southworth DANDY LIFT, Руководство пользователя

Результаты поиска

Содержание DANDY LIFT

Отзывы:

Похожие инструкции для DANDY LIFT

Бренды по названию

Популярные бренды