Southwest Windpower Whisper 100 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 42

Southwest Windpower Whisper 100 Скачать руководство пользователя страница 10

Whisper 100 Owners Manual

Document #0211 REV C

SOUTHWEST WINDPOWER

12/31/2005

Installation

Tower

Wind Generator Model

Whisper 100

Battery System Volts

12, 24, 36, 48

Minimum Amp x Hours
(20 hour rate)

200

Minimum Kilowatt Hours (Volts x Amps x Hours/1000)

4

Tower height minimum: 7m (20 ft) above trees or obsta-

cles within 100m (300 ft).

100m (300 ft)

1. TOWER LOCATION/TYPE AND

HEIGHT. INSTALL TOWER

(Install tower following manufacturer’s instructions.)

Tower height minimum is 7 meters (20 feet) above trees
or obstacles within 100m (300ft). The highest point on
your property is generally best, but wind generator dis-
tance to battery and the battery voltage determine the
correct wire size (Refer to wire size table pg. 6). A self
supporting tower occupies less ground area than a guyed
tower but is more expensive. A tilt-up design permits
easy installation and maintenance on the ground and
eliminates the need for climbing.

The Whisper 100 is suitable for side-of-building mount-
ing on

unoccupied

buildings such as garage or barn.

Some vibration transmission will be noticeable from
mounts to structure.
Foundations must be designed and approved for local
wind/soil conditions.

Consult with a professional engineer to determine
proper type and location of tower installation.

Side of Building Mount

Mounting

Bracket

MINIMUM BATTERY SIZES

1. Tower Installation

2. Battery Selection

See Table below for minimum battery size.

7

«
...
8
9
10
11
12
...
»

Содержание Whisper 100











































Отзывы:

Нет отзывов