background image

Questions? Call Toll Free at 1-800-737-2112 

 

Copyright © 2011 MAT Engine Technologies, LLC

Assembly

Parts Included With The Packaged Trimmer

Engine  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 cc, 2 cycle

Speed . . . . . . . . . . . . . . . . . . . . . . . . . . .  7,000-8,500 RPM 

Cutting Diameter  . . . . . . . . . . . . . . . . . . . .  15 in. (381 mm)

Line Diameter. . . . . . . . . . . . . . . . . . . . . .  0.080 in. (2 mm)

Spool Type . . . . . . . . . . . . . . . . . . .   Bump-Feed, Twin-Line

Fuel Tank Capacity. . . . . . . . . . . . . . . . . . . .  20 oz (600 ml)

Fuel Type . . . . . . . Unleaded Gasoline – 87 Octane or higher

2-Cycle Oil Type. . . . . . . . 2-Cycle Oil that meets or exceeds

 . . . . . . . . . . . . . . . . . . . . . . . . . . . JASO – FC Specifications   

Fuel Mixture . . . . . . . . . . . . . . . . 40:1 (Gasoline: 2-Cycle Oil)

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . NGK - BPMR7A

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  CHAMPION - CJ7Y

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  or equivalent

Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . 11.7 lbs (5.3 kg)

Product Specifications

• Save all instructions 

Parts & Features

•   Front Handle with Bolt and Nut 

•   Trimmer Guard with Bolt and Wing Nut

•   Spark Plug Wrench

•   40:1 2-Cycle Engine Oil (3.2 fl. oz.)

•   Operator’s Manual

If  you  need  assistance  or  find  any  parts 
missing, CALL TOLL FREE: 1-800–737-2112

 

2

3

4

5

6

7

15

8

11

14

10

12

13

1

16

1.

Trimmer Head Assembly

7.

On/Off Ignition Switch

13. Fuel Tank

2.

Bump Knob

8.

Recoil Starter Handle

14. Air Filter Cover

3.

Trimmer Guard

9.

Choke

15. Safety Lever

4.

Trimmer Line Knife

10. Fuel Primer Bulb

16. Spool Housing

5.

Front Handle

11. Spark Plug

6.

Throttle Lever

12. Muffler

Tools Needed For Assembly

•   10 mm wrench or adjustable wrench.

9

Do not operate Trimmer if it is damaged or not securely and fully assembled.

WARNING

Содержание S-HLT-2515-CB



















Отзывы: