South bend SB1108 Скачать руководство пользователя страница 48

Страница: 48 / 76

-46-

For Machines Mfd. Since 12/20

South Bend Tools

Model SB1108/SB1109

S E R V I C E

Table Parallelism Adjustments

The table is adjusted by turning the chain

sprockets underneath the table for movements

over 0.016" or by adjusting how the table is

mounted on the columns for movements under

0.016".

DISCONNECT MACHINE FROM POWER!

Remove motor access panel and locate chain

on underside of table.

Loosen lock bolts and idler sprocket (see

Figure 66).

NOTICE

When making adjustments, tighten fasteners

after each step to ensure the accuracy of your

tests. When adjusting the chain sprockets,

keep in mind that if the chain becomes too

loose, it will fall off of all the sprockets, and

returning it to its proper location can be

extremely difficult.

Mark location of one tooth of sprocket that

you are adjusting.

Carefully rotate sprocket (clockwise to lower

table; counterclockwise to raise table) just

enough to position next tooth at marked

location, then fit chain around sprocket

again.

Repeat

Steps 4–6 with each sprocket

that needs to be adjusted until table-to-

cutterhead clearance is within 0.016" from

one side to the other.

Make sure chain is properly fitted on

sprockets, then re-tighten idler sprocket and

lock bolts.

If necessary, micro-adjust table position by

loosening cap screws (see Figure 67) and

raising or lowering table until it is properly

aligned with cutterhead.

Note:

This process may require adjusting the

columns on both the left and right hand sides

until you find the correct combination.

10.

Re-tension table height chain (see

Tensioning Table Height Chain

instructions on Page 44).

To adjust table parallelism:

Move chain away from sprocket you want to

adjust so only that sprocket can be rotated

independent of chain.

Note:

If the left side of the table is too high,

the left two sprockets will need to be adjusted.

Each tooth on the sprocket represents 0.016"

of vertical movement as the cogs are turned.

Make sure, as you turn the sprockets, to keep

an accurate tooth count to ensure that the

table is adjusted equally.

Figure 67. Location of table micro-adjustment screws

(only one side shown).

Micro-Adjustment

Screws

Idler

Sprocket

Lock Bolts

Figure 66. Location of idler sprocket and chain tension

lock bolts.

Содержание SB1108













































































Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды

South bend SB1108, Руководство пользователя

Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды