South bend SB1108 Скачать руководство пользователя страница 30

Страница: 30 / 76

-28-

For Machines Mfd. Since 12/20

South Bend Tools

Model SB1108/SB1109

O P E R A T I O N

Feed Rate

Setting Feed Rate

Feed Rate ..............................................10–28 FPM

The infeed and outfeed rollers move the

workpiece through the planer while keeping it

flat and providing a consistent rate of movement.

The speed that these rollers move the workpiece

through the planer is the feed rate.

Generally, low feed rates are used for finishing

passes, while higher feed rates are used for

dimensioning passes.

Use the FEED SPEED control knob (see

Figure 26) to adjust the feed rate according

workpiece type and desired results.

Table Movement

One Full Revolution of Handwheel ..................

⁄

Material Thickness Range

SB1108 .......................................................

—

SB1109 .........................................................

⁄

" – 8"

The depth of cut on a planer means the amount

of material that is removed from the top of

the workpiece as it passes underneath the

cutterhead.

The depth of cut is set by adjusting the distance

of the table below the cutterhead. This distance

is the thickness of the workpiece minus the depth

of cut. The planing depth of cut is controlled by

using the table height handwheel on the right

side of the machine. Rotating the handwheel

clockwise raises the table.

Although the correct depth of cut varies

according to wood hardness and workpiece width,

we recommend the maximum depth of cut (per

pass) be no more than

⁄

". A series of light cuts

will give better end results and put less stress

on the planer than trying to take off too much

material in a single pass.

The depth of cut can be referenced directly from

the scale on the front of the planer, as shown in

the figure below.

Note:

The scale and digital readout function as a

general guide only, and is not intended for low-

tolerance, precision results. To ensure accuracy,

use a tape measure or caliper to measure your

workpiece thickness after each pass.

Depth of Cut

Figure 25. Location of table controls.

Table Height

Scale

Table

Height

Handwheel

Depth-of-Cut

Digital Readout

Figure 26. Feed speed control knob.

Feed Speed Control

Knob

Содержание SB1108













































































Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды

South bend SB1108, Руководство пользователя

Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды