South bend SB1108 Скачать руководство пользователя страница 31

Страница: 31 / 76

South Bend Tools

For Machines Mfd. Since 12/20

Model SB1108/SB1109

-29-

O P E R A T I O N

Bed Roller Height

Bed Roller Height Range ................. 0.002"–0.020"

Roller

Table

0.002"–0.020"

Figure 27. Recommended bed roller height above the

table surface.

The correct height of the bed rollers will vary,

depending on the type of material you intend to

plane. However, as a general rule, keep the bed

roller height range within the listed range above

the table surface, as illustrated.

When planing rough stock, set the rollers high

to keep the lumber from dragging along the bed.

When planing milled lumber, set the rollers low

to help minimize snipe.

To ensure accurate results and make the

adjustment process quicker and easier,

we recommend using a Rotacator (refer to

Accessories) to gauge the bed roller height from

the table surface. If a Rotacator is not available,

a straightedge and feeler gauges can be used, but

care must be taken to achieve accurate results.

Bed rollers that are not adjusted to the correct

height or out of alignment with each other

can cause poor finishes, inconsistent planing

thickness, and other undesirable results.

Items Needed

Qty

Hex Wrench 3mm .................................................1

Open-End Wrench 14mm .....................................1

Rotacator (optional, see Page 32) ........................1

Figure 28. Location of bed roller height controls (two

on each side of planer table).

Adjustment Cam

(1 of 4)

Set Screw

(1 of 4)

DISCONNECT MACHINE FROM POWER!

Completely lower table to give yourself

enough room to work.

Loosen set screw above each of four roller

adjustment cams—there are two on each

side of planer table (see Figure 28).

Rotate eccentric adjustment cams on each

side of roller to raise or lower bed rollers to

desired height above table surface.

Verify both sides of each roller are at the

same height, then re-tighten set screws to

secure in place.

IMPORTANT:

Bed rollers MUST be parallel

with the table.

Re-check roller heights to make sure they

did not change while being secured.

— If roller heights are not correct, repeat

this procedure until they are.

To adjust bed roller height:

Содержание SB1108













































































Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды

South bend SB1108, Руководство пользователя

Результаты поиска

Содержание SB1108

Отзывы:

Похожие инструкции для SB1108

Бренды по названию

Популярные бренды