1.800.338.7337 / www.soundoffsignal.com
TECHNICAL SPECIFICATIONS
Overall Dimensions: 1.55” H x 4.67” W x 0.98” D
Input Voltage Range:
10 - 30 Vdc
Current Consumption:
0.75 Amps max / module
(flash pattern dependent)
# of LEDs:
6 Generation 3 LEDs
Light Sync Technology:
Yes
Operating Temperature:
-40º to +65º C
Cruise Light Mode:
Yes
EGHSTE5(xx) 07.14
4.28
1.19
R0.23
3.81
0.72
Flash Patterns
Pattern Name
FPM
(Flashes per Minute)
1. Single
125
2. Double
125
3. Triple
123
ONE (1) LIGHT
Single Light Operation: Follow the ID Selection steps and set the ECE
GHOST to ID#1 if it is not already.
TWO (2) LIGHTS
ALTERNATING:
To obtain Alternating patterns, follow the ID
SELECTION steps and set one ECE GHOST to ID#1 and the other to
ID#3. Then proceed to the PATTERN SELECTION steps.
SIMULTANEOUS:
To obtain Simultaneous patterns, follow the ID
SELECTION steps and set both ECE GHOST lights to ID#1. Then
proceed to PATTERN SELECTION steps.
SLAVE MODE
The GHOST is capable of being activated through the use of a use sup-
plied flasher by putting it in slave mode.
1. Permanently connect the GHOST WHITE and BLACK wire to a good,
convenient ground.
2. Connect the GHOST RED wire, through a 5Amp fuse, to the output of a
+10-30 Vdc switching flasher.
PATTERN RESET
1. Remove power
2. Place WHITE (sync) wire to ground
3. With sync wire grounded, re-power RED wire
4. Maintain for one second (light will dim)
5. Remove power and ground (pattern 1 set)
ECE GHOST Sync Configuration Instructions
IMPORTANT! A MAXIMUM OF 4 SINGLE LIGHTS
CAN BE SYNCED TOGETHER
1. Set ID#
a. Identify which pattern and sequence you want and look up ID#
settings at right.
b. Connections
i. RED:
+12Vdc
ii. WHT: +12Vdc (Note: you will need to disconnect after
power is applied)
iii. BLK:
Ground
c. Apply power to unit
d. Without disconnecting power from unit, disconnect WHT
wire
e. Momentarily connect WHT to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 1 – 4
f. Disconnect power from unit to get out of ID mode.
2. Set Pattern
a. Reapply power to units.
b. Once all Light Head ID#s are configured, make sure all
lights are flashing the same pattern
c. Connect corresponding colored wires of all units together:
RED to RED, etc.
d. Change Pattern
i. Momentarily touch WHT wires to Ground
ii. Observe pattern change on all lights connected
e. Insulate all wires by taping with electrical tape
3. Connect Master Switch for Application
a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied
together
1 Cut hole in sheet metal
2 Press gasket into hole
3 Make wiring connections
4 Test
5 Install light
NOTE:
The GHOST is a factory sealed unit that CANNOT be serviced
in the field. Any attempt to gain access to the GHOST unit will
most likely cause permanent damage and void its warranty.
RECESS MOUNT ECE65 CERTIFIED
w/ STANDARD LENS
SINGLE LIGHT
EGHSTE5(x)B - Black
EGHSTE5(x)W - White
EGHSTE5(x)C - Chrome
RECESS MOUNT ECE65 CERTIFIED
w/ XYLEX LENS
SINGLE LIGHT
EGHSTE5(x)B-EU - Black
EGHSTE5(x)W-EU - White
EGHSTE5(x)C-EU - Chrome
