SoundCraft Spirit SX Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

background image

ELECTRIC GUITAR

• Some players prefer the sound of a valve amplifier, so be

prepared to mic up the speaker cabinet using a cardioid
dynamic mic.

• Experiment with mic positioning to achieve the desired

sound.

• If preferred, the guitar can be DI’d via a recording

preamp which incorporates an amp simulator.

Recommended effects/processor settings:

EQ:

Boost at: 120Hz to add ‘thump’ to rock guitars, 2-

3kHz to add bite, 5-7 kHz to add zing to clean rhythm
sound. Cut at: 200-300Hz to reduce boxiness, 4kHz and
above to reduce buzziness.

Compressor:

Attack between 10 and 50mS; Release,

around 0.3S, Ratio, between 4:1 and 12:1. Because of the
noise generated by a typical electric guitar, use in
conjunction with a gate or expander is advised.

Reverb:

Plate or room, 1.5 to 4S; 30 to 60mS pre-delay.

ACOUSTIC GUITAR

• Use the best mic that you can, preferably a condenser

type.

• For a natural tone, position the mic between 12-18ins

from the guitar, aiming at where the neck joins the body.

• If recording in stereo, point a second mic towards the

centre of the neck, about 12-18ins from the instrument.

• Acoustic guitars sound best in slightly live rooms, if

necessary place a piece of acoustically reflective board
beneath the player.

Recommended effects/processor settings:

EQ:

Boost: between 5kHz and 10kHz to add sparkle. Cut

between: 1kHz and 3kHz to reduce harshness, 100 and
200Hz to reduce boom. In busy pop mixes you can cut the
low end to produce a more cutting rhythm sound.

Compressor:

Attack 20 mS; Release, around 0.5S, Ratio,

between 4:1 and 12:1.

Reverb:

Bright setting such as Plate to add vitality. Decay

time of between 2 to 3S.

BASS GUITAR

• Most engineers DI the bass via an active DI box and a

compressor. This provides a clearer sound.

• Use the compressor to keep signal peaks under control.
• Check the player’s technique; the harder the instrument

is played, the brighter the tone.

• Consider the use of a budget graphic EQ.

Recommended effects/processor settings:

EQ:

Boost: at 80-100Hz to add more weight and punch,

between 2 and 4kHz to add edge. Cut: below 50Hz to

SECTION 6: In the Studio

29

Control

Room

L&R

Mic

Line

Insert

Tape Return

Tape Send

2 T

rack

Mix L&R

Inserts

M U L T I T R A C K R E C O R D I N G & M I X D O W N

NEARFIELD
MONITOR

NEARFIELD
MONITOR

DAT

RECORDER

PROCESSORS

(NOISE GATES,

COMPRESSOR/LIMITERS,

AURAL EXCITERS)

MULTITRACK

RECORDER

INSTRUMENTS

To Line Inputs

MICROPHONES

To Mic Inputs

STEREO

POWER AMP

FIG. 6.4

13924 Inners 7/8/01 2:56 pm Page 29

«
...
27
28
29
30
31
...
»

Содержание Spirit SX









































Отзывы:

Нет отзывов

Похожие инструкции для Spirit SX

Бренд: Alto Страницы: 16

Бренд: Waring Страницы: 8

Бренд: FAME Страницы: 17

Бренд: Gastrodomus Страницы: 37

Бренд: Jata electro Страницы: 20

Бренд: TREVIDEA Страницы: 12

Kitchen machine with attachments

Бренд: Morphy Richards Страницы: 9

Бренд: MFB Страницы: 2

Бренд: Koma Elektronik Страницы: 2

Бренд: GE Страницы: 20

Бренд: GE Страницы: 28

Бренд: GE Страницы: 24

Бренд: GE Страницы: 12

Xcellerex XDM 100

Бренд: GE Страницы: 322

Бренд: GE Страницы: 4

Бренд: Harbinger Страницы: 16

Бренд: Harbinger Страницы: 20

Бренд: Shure Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды