Sound Skulptor EQ573-II Скачать руководство пользователя | Manualshive

Страница: 4 / 11

background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 27/05/21

EQ573-II Assembly guide – Main board

9. Test pins

Solder the 7 test pins TP1, TP2, TP3, TP4, 0V, V+, V-.

10. Tantalum capacitors

Add C61, C69. The plus lead is the longest.

Warning

: The +lead must go into the +hole. Do not reverse !

11. Transistors

Add Q1 to Q6.

Warning

: Watch out the transistor direction.

12. Non polarized electrolytic capacitors

Add C9, C10, C11, C12.
These caps are not polarized and can be inserted in any direction.

Copyright ©2020 to today SoundSkulptor

«
...
2
3
4
5
6
...
»

Содержание EQ573-II












Отзывы:

Нет отзывов

Похожие инструкции для EQ573-II

Бренд: Harman Kardon Страницы: 13

Бренд: Aiwa Страницы: 20

BeoSound 3000 2671

Бренд: Bang & Olufsen Страницы: 68

Бренд: Vivax Страницы: 68

Бренд: McIntosh Страницы: 32

MEISTERSTUCK SO-610

Бренд: Sonoro Страницы: 334

Бренд: Exibel Страницы: 32

Бренд: Technika Страницы: 16

Бренд: Panasonic Страницы: 72

Бренд: Pioneer Страницы: 5

Бренд: Pioneer Страницы: 22

Бренд: Pioneer Страницы: 96

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды