Sound Skulptor EQ573-II Скачать руководство пользователя

Страница: 8 / 11

www.soundskulptor.com

Document revision 1.1 – Last modification : 27/05/21

EQ573 Assembly guide – Potentiometers board

27. Resistor

Add the resistor R17 horizontally (green identifier in the parts list).

28. Potentiometers

Add P1 and P3 (10KA). Insert the potentiometers into the PCB holes from the solder side, making sure
the pins fit into the corresponding PCB pads. Attach with washer and nut on the components side, then
solder.
Add P2 (47KA) in the same way.

29. 2x5 pins connector J7a

Insert and solder 2x5 pins header.

Warning

: Make sure to sit them perfectly flat on the PCB for a good position match with the switches

board.

30. Shaft adapters

Insert the three shaft
adapters on the three
potentiometers. Attach
with three headless

screws.

EQ573 Assembly guide – Final assembly

31. Switch board and potentiometer board assembly

Insert the potentiometer shafts into the rotary switches hollow shafts, taking care of the connector
matching. Attach with three M2.5x8mm screws.

Содержание EQ573-II












Результаты поиска

Содержание EQ573-II

Отзывы:

Похожие инструкции для EQ573-II

Бренды по названию

Популярные бренды

Sound Skulptor EQ573-II, Инструкция по сборке

Результаты поиска

Содержание EQ573-II

Отзывы:

Похожие инструкции для EQ573-II

Бренды по названию

Популярные бренды