Sound Skulptor EQ573-II страница 5 Скачать руководство пользователя | Manualshive

Страница: 5 / 11

background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 27/05/21

EQ573-II Assembly guide – Main board

13. Electrolytic capacitors

Add all the other electrolytic capacitors of the main PCB.

Warning

: The +lead must go into the +hole. Do not reverse (they may explode !)

14. Link Connector J2

Solder the connector header J2. Solder one pin first, check verticality, then solder the other pins.

Warning

: Check the direction.

15. Inductors

Solder L1 and L2.

16. U1, U2

Insert the two integrated circuits U1and U2 into their respective sockets.

Warning

: these two parts are different and have a direction identified by a notch or a dot.

Copyright ©2020 to today SoundSkulptor

«
...
3
4
5
6
7
...
»

Содержание EQ573-II












Отзывы:

Нет отзывов

Похожие инструкции для EQ573-II

Бренд: Laser Страницы: 3

Бренд: AML Страницы: 46

Бренд: Jaycar Страницы: 8

Audio Everywhere

Бренд: Listen Technologies Страницы: 2

Бренд: TDM-Audio Страницы: 17

Бренд: Z Systems Страницы: 10

2-661-374-11(4)

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 92

3-097-194-15(1)

Бренд: Sony Страницы: 112

Бренд: Silvercrest Страницы: 24

Бренд: Silvercrest Страницы: 35

Бренд: Silvercrest Страницы: 42

Бренд: Silvercrest Страницы: 58

Бренд: Silvercrest Страницы: 62

Бренд: Welton USA Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды