Sorel MTDC Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

Sorel MTDC Скачать руководство пользователя страница 32

32

Special functions

6.5.6. - Anti Legionella

6.5.6.2. - AL T set

This function is used to heat up the system during selected periods to eliminate

legionella bacteria.

This temperature has to be detected for the time set in AL residence time at the

AL sensors for a successful heat up.

This determines the time span for which the AL T set temperature must be de-

tected for a successfull AL heat up.

Caution

The anti-Legionella function is switched off at delivery.

Whenever heating-up has been carried out with the anti-Legionella

function switched on, an information message with the date appears

on the display.

During the anti-Legionella function the storage tank is heated up

over the set value “Tmax S(X)”, which can lead to scalding and

damage to the system.

Danger

This anti-Legionella function does not provide complete protection

against Legionella, because the controller is dependent on suffi cient

energy being fed in, and it is not possible to monitor the temperatu-

res in the entire range of the storage tanks and the connected piping

system. To provide complete protection against Legionella bacteria, it

must be ensured that the temperature is raised to the necessary tem-

perature, and at the same time there must be water circulation in the

storage tank and piping system by means of other additional energy

sources and external control units.

Caution

6.5.6.3. - AL residence time

6.5.6.4. - Last AL heat

This displays the date and time of the last successful heat up.

This temperature is used to measure the AL temperature.

6.5.6.5. - AL sensor 1

Optional AL sensor

When a second sensor is connected, both sensors must reach and hold the set-

point temperature for the residence time for a successful heat up.

6.5.6.6. - AL Sensor 2

During this periods the AL heat up is attempted.

R

el

ay

fu

nc

tion

s

6.5.6.7. - AL-times

«
...
30
31
32
33
34
...
»

Содержание MTDC

















































Отзывы:

Нет отзывов