Sorel FWC 5 Скачать руководство пользователя страница 31

31

If the mains voltage is switched on and the con-
troller still does not function or display anything, 
then the internal device fuse may be defective. 
In that case, open the device as described un-
der 3.1, remove the old fuse and check it.
Exchange the defective fuse for a new one, lo-
cate the external source of the error (e.g. pump) 
and exchange it. Then 

fi

 rst recommission the 

controller and check the function of the switch 
outputs in manual mode as described under 
9.2.

Danger

Danger

 Fig.3.1.1  

Fuse

Maintenance

Z.2.  Replacing the fuse

Repairs and maintenance may only be performed by a specialist. Befo-
re working on the unit, switch off the power supply and secure it against 
being switched on again! Check for the absence of power!

Only use the supplied spare fuse or a fuse of the same design with the follo-
wing speci

fi

 cations: T2A 250V

In the course of the general annual maintenance of your heating system you 
should also have the functions of the controller checked by a specialist and 
have the settings optimised if necessary.

Performing maintenance:
- Check the date and time (see 11.1)
- Assess/check plausibility of analyses (see 7.)
- Check the error memory (see 7.5)
- Verify/check plausibility of the current measurement values (see 
6.)
- Check the switch outputs/consumers in manual mode (see 9.2)
- Poss. optimise the parameter settings

Caution

Maintenance

Z.3.  Maintenance

Содержание FWC 5

































Отзывы: