Sorel FWC 5 Скачать руководство пользователя страница 24

24

Special functions

All of the settings that have been made can be reset, thus returning the controller to its delivery 
state.

6.4   Factory settings

Caution

The entire parametrisation, analyses, etc. of the controller will be lost 
irrevocably. The controller must then be commissioned once again.

6.5.1

 

Turn time

The time in seconds the mixer is switched on (opening or closing), before a new measurement 
for the regulation of the 

fl

 ow temperature is performed.

Settings range: 0.1 sec. to 3 sec. / Default: 2 sec.

6.5.2 Pause factor

Set a value to multiply the calculated pause time with. e.g. a value of 1 would use the 
calculated pause time, 0.5 would half the pause time, and 4 quadruple the calculated pause 
time.

Settings range: 0.1 to 4.0 /  Default: 3.0

6.5.3 Increase

If a fast increase of temperature occurs, this value is added to the 

fl

 ow temperature, so that 

the mixer reacts faster. Once the temperature rises no faster, the measured temperature is 
used again. Temperature is measured once every minute.

Settings range: 0 to 20 / Default: 0

6.5 Mixer

Caution

Settings are only to be made during the installation by a specialist. Incorrect 
settings may cause severe malfunctions.

Содержание FWC 5

































Отзывы: