46
Basic Operations of the Function Menu
Ch
apt
er 3 Prep
ar
at
ion
s
a) When the maintenance menu item M22: OPTION SETTING >DVB-ASI
is set to “on” with the optional PDBK-202 being installed
P3 AUDIO page
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to “REC” or “PB”.
• Set setup menu item 131 AUDIO VOLUME to “each”.
P4 TC page
F4: A8 INPUT
Selects the audio input signal to assign
to audio channel 8.
SDI:
Audio signal embedded into SDI
signal
ANALOG2:
Input signal to the ANALOG
AUDIO INPUT 2 connector
AES/EBU8:
Signal input to the DIGITAL
AUDIO (AES/EBU) IN 7/8
connectors
DVB-ASI:
DVB-ASI TS signal
a)
F5: –
(Unassigned function button)
F6: –
(Unassigned function button)
Item
Setting
F1: A5 VOL
Sets the volume of audio channel 5.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to +12
dB)
by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F2: A6 VOL
Sets the volume of audio channel 6.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to +12
dB)
by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F3: A7 VOL
Sets the volume of audio channel 7.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to +12
dB)
by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F4: A8 VOL
Sets the volume of audio channel 8.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to +12
dB)
by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F5: –
(Unassigned function button)
F6: –
(Unassigned function button)
Item
Setting
Item
Setting
F1: TCG
Selects the timecode signal to which the
internal timecode generator
synchronizes.
INT:
Follow the initial value set from the
front panel or remotely from the
device connected to a REMOTE
(9P) connector.
EXT:
Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SYS:
Synchronize to standard reference
timecode signal broadcast station
input to the SYSTEM TC INPUT
connector.
SDI:
Synchronize to timecode
embedded into HD-SDI or SD-SDI
signal input to the HD/SD-SDI
INPUT connector.
Note
If you select “EXT” or “SDI” when a DVB-
ASI TS signal is input, the internal
timecode generator synchronizes to
timecode data contained in the TS
signal.
F2: PRST/RGN
Selects the following for the internal
timecode generator.
PRESET:
Presets an initial value for the
timecode generated by the internal
timecode generator, as specified
from the front panel or remotely from
the device connected to a REMOTE
(9P) connector.
TC:
Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC:
Generate timecode synchronized
to VITC read by the internal
timecode reader.
F3: RUN MODE
Selects the timecode run mode.
FREE RUN:
Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN:
Timecode advances only
during recording. When you select
this item, also set F1: TCG on this
page to “INT” and set F2: PRST/
RGN to “PRESET”.
F4: DF/NDF
Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF:
Drop-frame mode
NDF:
Non-drop-frame mode
F5: PDPSET
When the system frequency is set to
1080/59.94i, 1080/29.97P, or 720/
59.94P, presets the timecode of the A
frame of the pulldown sequence.
24F TC:
Reference timecode for A frame
30F TC:
Timecode after pulldown
conversion from 24-frame timecode