Sony Walkman MZ-N910 страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 65

background image

29

MZ-N910

Rewriting the Patch Data at Replacement of Main Board (Ver. 1.400)

This set requires the patch data in the nonvolatile memory (IC851) to be rewritten using the application, when the MAIN board was
replaced.

Caution: The application that meets the microcomputer version in this set must be used when rewriting the patch data. Rewriting the

patch data using the application not suitable for the microcomputer version could cause the set to malfunction.
For a checking method of the microcomputer version, see “SECTION 4 TEST MODE” (page 11).

• Preparation

1. USB cable (attached to the set)
2. Personal computer in which the Net MD Driver has been installed. (For further information, see “System requirements” (page 4) in

“SECTION 1 SERVICING NOTES”)

3. Application “USB PatchWriter” for patch data rewriting

• How to get the application “USB PatchWriter” for patch data rewriting

Contact our service technical support section for PA products to get the application.

• Pre-check

1. Check the microcomputer version in this set. (For a checking method of the microcomputer version, see “SECTION 4 TEST MODE”

(page 12).)

2. Check that the Net MD Driver has been installed in the personal computer.
3. Make sure that the set is in the Normal mode.

Note:

Do not rewrite the patch data in the Test mode.

• Rewriting the patch data

1. Connect the set to the personal computer with the USB cable.
2. Start the application “USB PatchWriter”.
3. Make sure that the following window opens.
4. Click the [USB CONNECT] button.

«
...
27
28
29
30
31
...
»

Содержание Walkman MZ-N910


































































Отзывы:

Нет отзывов

Похожие инструкции для Walkman MZ-N910

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 16

Бренд: Hama Страницы: 12

Бренд: Yamaha Страницы: 32

Бренд: Westfalia Страницы: 19

Бренд: Daewoo Страницы: 58

MVDP1085 - DVD Player - 8.5

Бренд: Memorex Страницы: 94

Бренд: MAJORITY Страницы: 16

Бренд: Denver Страницы: 12

Бренд: Zenith Страницы: 36

Бренд: Coby Страницы: 15

Бренд: Mach Speed Technologies Страницы: 42

Бренд: Grundig Страницы: 6

Бренд: Oakcastle Страницы: 16

Бренд: Vitek Страницы: 6

Бренд: Craig Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды