Sony Walkman MZ-N910 страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 65

background image

33

MZ-N910

Rewriting the NV values (Ver. 1.400)

Caution: The application that meets the microcomputer version in this set must be used when rewriting the NV values. Rewriting the NV

values using the application not suitable for the microcomputer version could cause the set to malfunction.
For a checking method of the microcomputer version, see “SECTION 4 TEST MODE” (page 12).

• Preparation

1. USB cable (attached to the set)
2. Personal computer in which the Net MD Driver has been installed. (For further information, see “System requirements” (page 4) in

“SECTION 1 SERVICING NOTES”)

3. Application “NVWriter” for NV values rewriting

• How to get the application “NVWriter” for NV values rewriting

Contact our service technical support section for PA products to get the application.

• Pre-check

1. Check the microcomputer version in this set. (For a checking method of the microcomputer version, see “SECTION 4 TEST MODE”

(page 12).)

2. Check that the Net MD Driver has been installed in the personal computer.
3. Make sure that the set is in the Normal mode.

Note:

Do not rewrite the NV values in the Test mode.

• Rewriting the NV values

1. Connect the set to the personal computer with the USB cable.
2. Start the application “NVWriter”.
3. Make sure that the following window opens.
4. Click the [USB CONNECT] button.

«
...
31
32
33
34
35
...
»

Содержание Walkman MZ-N910


































































Отзывы:

Нет отзывов

Похожие инструкции для Walkman MZ-N910

Бренд: D-Link Страницы: 18

Бренд: Samsung Страницы: 27

Бренд: Magnavox Страницы: 20

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 3

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 7

Yepp Sports YP-60

Бренд: Samsung Страницы: 2

Yepp Sports YP-60

Бренд: Samsung Страницы: 40

Napster YH-920GS

Бренд: Samsung Страницы: 32

Napster YH-920GS

Бренд: Samsung Страницы: 25

Napster YH-920GS

Бренд: Samsung Страницы: 2

Бренд: IAdea Страницы: 4

Бренд: Mystery Страницы: 36

Бренд: Linn Страницы: 34

Бренд: Magnavox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды