STR-DN1000
62
DIGITAL VIDEO BOARD IC3000 R5F3640DDFBR-128 (HDMI CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 5
NC
O
Not used
6
BYTE
I
External data bus width selection signal input terminal “L”: 16 bit Fixed at “L” in this set
7
CNVSS
I
Processor mode selection signal input terminal “L”: single chip mode
Fixed at "L" in this set
8, 9
NC
O
Not used
10
RESET
I
Reset signal input from the system controller “L”: reset
11
XOUT
O
System clock output terminal (10 MHz)
12
VSS
-
Ground terminal
13
XIN
I
System clock input terminal (10 MHz)
14
VCC_3.3V
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal Not used
16 to 18
NC
O
Not used
19
RX_RST
O
Reset signal output to the HDMI receiver “L”: reset
20
RX_INT
I
Interrupt signal input from the HDMI receiver
21
1444_HPD
O
Hot plug detection control signal output to the HDMI input selector
22
HPD_IN1
O
Hot plug detection control signal output to the HDMI IN 1 connector
23 to 26
NC
O
Not used
27
CSCL
O
I2C clock signal output to the EEPROM, HDMI receiver and HDMI transmitter
28
CSDA
I/O
I2C data bus with the EEPROM, HDMI receiver and HDMI transmitter
29
232COUT (VU TX)
O
Serial data output to the connector (for RS-232C) and DSP
30
232CIN (VU RX)
I
Serial data input from the connector (for RS-232C) and DSP
31
CLK 1
O
Not used
32
RTS 1
O
Not used
33
VUCOM_SDA
I/O
I2C data bus with the system controller
34
VUCOM_SCL
I
I2C clock signal input from the system controller
35
EDID_SELA
O
Write protect signal output to the EEPROM
36
EDID_SELB
O
Input data selection signal output to the data selector
37 to 39
NC
O
Not used
40
VDAC_RESET
O
Not used
41
TX_5VPWR
O
Power supply on/off control signal output terminal for HDMI OUT connector “H”: power on
42
TX_RST
O
Reset signal output to the HDMI transmitter “L”: reset
43
TX_INT
I
Interrupt signal input from the HDMI transmitter
44 to 50
NC
O
Not used
51 to 53
1444_SELA to
1444_SELC
O
HDMI input selection signal output to the HDMI input selector
54
1444_OEB
O
Output enable signal output to the HDMI input selector
HDMI +5V power input selection signal output terminal
Not used
Power supply terminal (+3.3V)
Not used
Ground terminal
Not used
Non-LPCM setting signal output to the DSP “L”: LPCM
Error signal output to the system controller and DSP
Not used
91 to 93
MODEL_SW1
I
Model setting terminal
94
AVSS
-
Ground terminal
95
NC
O
Not used
96
VREF
I
Reference voltage (+3.3V) input terminal
97
AVCC
-
Power supply terminal (+3.3V)
98 to 100
NC
O
Not used
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
