Case 5
When starting the Converter Setup Utility, the
“IP Address Setup” dialog box appears.
If communication cannot be established with the current IP address of the computer connected to the
Wireless LAN Converter and the IP address of the Wireless LAN Converter, the dialog box above
appears.
Verify that the IP address of the Wireless LAN Converter is acceptable, and click “Execute Setup”.
The IP address of the Wireless LAN Converter is temporarily changed so that the computer can open
the Wireless LAN Converter Setup Page.
Note
If the computer connected to the Wireless LAN Converter is also connected to another network, make sure that the
new IP address does not duplicate the address of a device on that network.
z
Hint
When you turn off or restart the Wireless LAN Converter, the IP address reverts to its original setting.
Case 6
Cannot display the Wireless LAN Converter Setup
Page.
1
Is the temporary address assigned to the Wireless LAN
Converter used by another device or computer on the
network?
1
Disconnect and reconnect the power cord of the Wireless Unit cable to restart the
Wireless LAN Converter.
2
Start the Converter Setup Utility.
3
In the “IP Address Setup” dialog box, replace the current Wireless LAN Converter IP
address with an unused address, and then click “Execute Setup”.
2
Is the Web browser of the computer used for the Wireless
LAN Converter setup configured to use a proxy server?
Make sure that no proxy setting is enabled for the IP address of the Wireless LAN Converter.
For details, see case 14.
Case 7
On the Wireless LAN Converter Setup Page, the
“WEP Key” text box cannot be used.
Did you select “Enabled” under “Encryption (WEP)”?
The “WEP Key” text box is only available if the “Enabled” setting is selected for “Encryption (WEP)”.
Set “Encryption (WEP)” to “Enabled”, select the “Key Length” and “WEP Key Type”, and then enter
the encryption (WEP) key in the “WEP Key” text box. The prescribed length of the string depends on
the “Key Length” setting. Check the indication above the text box.
Case 8
The Status indicator is slowly flashing white, but
communication with the access point is not possible.
Did you make the correct security settings?
Even if the network name (SSID) is correct, if the security settings are incorrect, communication with
the access point is impossible. Verify your access point security settings, and change any Wireless LAN
Converter security settings accordingly.
Case 9
Unable to connect after the access point settings
are changed.
Did you also change Wireless LAN Converter settings?
If the network name (SSID) or security settings are changed, the Wireless LAN Converter settings must
also be changed to match these new settings. Refer to “If You Change the Access Point Settings” in the
Quick Start Guide to change the settings of the Wireless LAN Converter.
Case 10
Unable to connect after the access control (MAC
address filtering) of the access point is enabled.
When setting up the access control of the access point, input the MAC address of the Wireless LAN
Converter, and then the MAC address of the device connected to the Ethernet. The Wireless LAN
Converter first connects with its own address, then switches to the one of the wireless communication
devices. Some printers require that you set both addressed to be able to connect to them.
Case 11
Cannot create a peer-to-peer network
You cannot connect wireless PC cards that only support 2.4 GHz to a 5 GHz wireless network.
1
Click “Start”, and then click “Control Panel”.
2
In “Control Panel”, click “Network and Internet Connections”, and then click
“Network Connections”.
z
Hint
If “Network and Internet Connections” does not appear, click “Switch to Category View” on the left.
3
In the “Network Connections” window, right-click the Wireless Network Connection
icon that you want to use, and click “Properties”.
4
Click the “Advanced” tab and (if selected) clear the “Protect my computer and
network by limiting or preventing access to this computer from the Internet” check
box.
5
Click “OK”.
z
Hint
Refer to Windows XP Help for details about the “Internet Connection Firewall” function.
Note
Make sure that you take appropriate security measures when the “Internet Connection Firewall”
function is disabled. Except when configuring the Wireless LAN Converter or access point, it is strongly
recommended that you enable the “Internet Connection Firewall” function at all times.
■
When using a personal firewall software provided standalone
or as part of an antivirus or network security software
Antivirus scanning and network security software sometimes includes a function called a
“personal firewall”, intended to prevent unauthorized access by other computers. Depending on
the software, the security level of this function may initially be set to a high level. If this high
security level setting is left enabled, other computers may be unable to access your computer. This
can cause problems such as not being able to connect to the network when changing the Wireless
LAN Converter or access point settings. In this event, lower the security level to allow the
network connection. Refer to the software instructions or Help for details.
Notes
• Make sure that you take appropriate security measures.
• For questions about firewall functions, contact your firewall software manufacturer.
■
Proxy settings
Make sure that no proxy settings are enabled for the IP address of the Wireless Broadband Router.
Note
While the proxy server settings are disabled, it may not be possible to display other pages except the Wireless
Broadband Router Setup Page.
Example 1: Using Microsoft Internet Explorer
1
On the “Tools” menu, click “Internet Options”.
The “Internet Options” dialog box appears.
2
On the “Connection” tab, click “LAN Settings”.
The “Local Area Network (LAN) Settings” dialog box appears.
3
If the “Use a proxy server for your LAN (These settings do not apply to dial-up or VPN
connections)” check box is selected, clear the check box and click “OK”.
4
When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
Example 2: Using Netscape
1
Start the Web browser on the computer used for the Wireless Broadband Router
setup.
2
On the “Edit” menu, click “Preferences”.
3
In “Category”, click “Advanced” and click the “Proxies” button.
4
Select “Direct connection to the Internet” and click “OK”.
5
When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
■
Java settings
Make sure that the Java settings of your Web browser are enabled. If they are not, do so.
The Super A/G and Turbo Mode functions of the PCWA-DE80 are supported by the Wireless
Broadband Router PCWA-AR800. Compatibility of the Super A/G and Turbo Mode functions
with third party access points is not guaranteed.
Quick Setup
switch
Reset switch
Case 12
Cannot communicate with a device other than the
computer used for setup.
1
Did you set up the device correctly for use on a network?
Configure the required settings to enable the device on a network. For details, refer to the
documentation of the device.
2
Did you connect the device correctly to the Wireless LAN
Converter?
Verify that connections are established as shown below.
3
Did you wait a few moments when changing the connection
from the computer used for setup to the other device?
After disconnecting the cable from the computer used for setup, do not plug it immediately into
the new device. Wait at least 10 seconds before plugging it.
z
Hint
The device information accumulated on the computer takes about 10 seconds to be deleted.
Case 13
Forgot settings or want to reset.
When the Wireless LAN Converter is on, use a paper clip or a similar
object to hold down the reset switch located on the bottom of the
Wireless LAN Converter. Release the switch when the Status indicator
starts to flash red.
The Wireless LAN Converter restarts automatically and all settings
revert to the factory defaults. Configure the Wireless LAN Converter
again as needed.
Note
Be careful not to press the Quick Setup switch when you reset the Wireless
LAN Converter. Pressing the Quick Setup switch does not reset the Wireless
LAN Converter.
Case 14
What are the factory default settings?
The factory default settings are as follows.
Item
Setting
Network Name (SSID)
–
Security
Disabled
Available Band
5 GHz & 2.4 GHz
Connection Mode
Access Point Network
IP Address Setting
Obtain an IP address automatically (DHCP)
Quick Setup Switch
Enabled
Status Indicator
On
Note
In the table above, “–” indicates blank settings.
Case 15
What are the Wireless LAN Converter functions
and how can I make advanced settings?
Click “Start”, point to “Programs” (“All Programs” when using the Windows XP operating
system), “Wireless LAN”, and click “Converter Setup Help”.
Help appears.
z
Hint
For updates and connection information, refer to product information and Q&A search at the Sony Online Support
(http://www.sony.com/wirelesslansupport).
Case 16
Computer firewall function and browser proxy
settings
■
The “Internet Connection Firewall” function is enabled
When the Windows XP “Internet Connection Firewall” function is enabled, it may prevent the
computer from being accessed externally (this function is disabled by default). This function can
prevent connection to your network when you change your Wireless LAN Converter or access
point settings. If this happens, disable the “Internet Connection Firewall” function as described
here, connect to the network, and then re-enable the function.
Power cord
Power Unit
Wireless Unit
Wireless Unit cable
Ethernet cable
(not included)
To power outlet
