Chapter 11
Setup Menus
11-20
Chapter 11
Setup Menus
11-4 Items in the Extended Setup Menu
Menu items in the range 800 to 899, relating to audio control (Continued)
Item number
Item name
Settings
806
LEVEL METER SCALE
Select the mode in which digital audio levels are displayed.
PEAK.0 :
Displays the audio level as negative values with the maximum level set
to 0 dB.
REF.0:
Displays the audio level as positive and negative values with the
reference level set to 0 dB.
809
AUDIO LEVEL METER
DIMMER CONTROL
Set the brightness of the audio level meters.
0 ... 7:
Set in this range. 0 is the brightest, and 7 the dimmest.
807
AUDIO OUTPUT PHASE
Select the output timing of digital audio playback signals: (SDI and AES/EBU
only). The reference position corresponds to a setting of 80H; when the setting
is less than 80H, the output timing is advanced, and when it is higher than 80H,
the output timing is delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1
sample=approx. 20 µs)
0 ... 80 ... FF :
Setting in this range
808
INTERNAL AUDIO
SIGNAL GENERATOR
Select the operation of the internal audio test signal generator.
off :
No operation
SILNC:
Silent signal
1KHZ:
At 1 kHz, –20 dB FS sine wave is supplied to all audio input channels.
824
ANALOG LINE OUTPUT
SELECT
Select the analog audio signals (tracks 1 to 8) to be assigned to audio output
channels 1 to 4.
Sub-item
1
CH1/CH2
tr1/2 :
Tracks 1 and 2 assigned to audio output channels 1 and 2
tr3/4:
Tracks 3 and 4 assigned to audio output channels 1 and 2
tr5/6:
Tracks 5 and 6 assigned to audio output channels 1 and 2
tr7/8:
Tracks 7 and 8 assigned to audio output channels 1 and 2
2
CH3/CH4
tr1/2:
Tracks 1 and 2 assigned to audio output channels 3 and 4
tr3/4 :
Tracks 3 and 4 assigned to audio output channels 3 and 4
tr5/6:
Tracks 5 and 6 assigned to audio output channels 3 and 4
tr7/8:
Tracks 7 and 8 assigned to audio output channels 3 and 4
823
NON-AUDIO FLAG PB
Controls the non-audio flag when the playback format is Digital Betacam or
Betacam SX.
Sub-item
1
CH1/CH2
During playback (except in audio test signal output), sets the digital audio non-
audio flag as follows.
off :
OFF (the data is audio)
on:
ON (the data is non-audio)
AUTO:
As follows, depending on whether tape data has been confirmed.
• Tape data has been read and confirmed: ON or OFF, according to the data.
• Tape data has not been confirmed: Current state is maintained.
Notes
• During playback of analog tapes, the non-audio flag is OFF regardless of the
setting of this item.
• In the MPEG IMX format, during playback, and in audio test signal output, the
non-audio flag follows the setting of maintenance menu item M372. (SY
software versions before 3.05)
• In the MPEG IMX format, operation is the same as for the OFF setting or AUTO
setting, and for audio test signal output follows maintenance menu M372. (SY
software version 3.05 and later)
For more information about the maintenance menu item M372, refer to the
Maintenance Manual.
(Continued)
2
CH3/CH4
3
CH5/CH6
Valid only for an
MPEG IMX format
8-channel
recording tape
4
CH7/CH8
Valid only for an
MPEG IMX format
8-channel recording
tape