Sony MDS-SE9 Скачать руководство пользователя страница 64

Страница: 64 / 77

MDS-SE9

8-1. OVERALL SECTION

Ref. No.

Part No.

Description

Remarks

Ref. No.

Part No.

Description

Remarks

front panel section

chassis section

MD mechanism deck section-1
(MDM-7S2D)

not

supplied

not

supplied

not

supplied

3-970-608-01 SUMITITE (B3), +BV

4-231-555-01 INSULATOR

4-228-643-21 SCREW (+BVTTWH M3), STEP

4-221-580-01 SCREW, CASE

4-245-364-01 CASE

1-775-153-11 WIRE (FLAT TYPE) (17 CORE)

1-775-238-11 WIRE (FLAT TYPE) (27 CORE)

1-827-037-11 CORD (WITH CONNECTOR) 7P

4-231-113-01 SCREW (1.7X3), BTN

1-777-071-63 CORD, POWER

4-217-350-11 STOPPER, CORD

7-685-646-79 SCREW +BVTP 3X8, TYPE2, IT-3

SECTION 8

EXPLODED VIEWS

NOTE:

•

-XX, -X mean standardized parts, so they may
have some differences from the original one.

•

Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.

•

The mechanical parts with no reference
number in the exploded views are not supplied.

The components identified by mark

dotted line with mark

are critical for safety.

Replace only with part number specified.

Содержание MDS-SE9














































































Результаты поиска

Содержание MDS-SE9

Отзывы:

Похожие инструкции для MDS-SE9

Бренды по названию

Популярные бренды

Sony MDS-SE9, Руководство по обслуживанию

Результаты поиска

Содержание MDS-SE9

Отзывы:

Похожие инструкции для MDS-SE9

Бренды по названию

Популярные бренды