Sony MDS-SE9 Скачать руководство пользователя страница 26

Страница: 26 / 77

MDS-SE9

• For details of each adjustment mode, refer to “SECTION 6 ELECTRICAL ADJUSTMENTS”.

About “Err Display” (C02), please refer to a page 7 self-diagnostic function.

• If a different mode has been selected by mistake, press the

[MODE]

button to release that mode.

• Modes with (

) in the Mark column are not used for servicing and therefore are not described in detail. If these modes are set acciden-

tally, press the

[MODE]

button to release the mode immediately.

5-1. Operating the Continuous Playback Mode

Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2) Press the

button to display “CPLAY 2MODE” (C36).

(3) Press the

[ENTER/START]

button to change the display to “CPLAY2MID”.

(4) When access completes, the display changes to “C =

AD =

)”.

Note: The numbers “ ” on the display show you error rates and ADER.

Changing the parts to be played back
(1) Press the

[ENTER/START]

button during continuous playback to change the display as below.

When pressed another time, the parts to be played back can be moved.

(2) When access completes, the display changes to “C =

AD =

)”.

Note: The numbers “ ” on the display show you error rates and ADER.

Ending the continuous playback mode
(1) Press the

[MODE]

button. The display will change to “CPLAY 2MODE” (C36).

(2) Press the

button and take out the disc.

Note : The playback start addresses for IN, MID, and OUT are as follows.

: 40h cluster

MID

: 300h cluster

OUT

: 700h cluster

Display

AUTO CHECK

Err Display

TEMP ADJUST

LDPWR ADJUST

Iop Write

Iop NV Save

EF MO ADJUST

EF CD ADJUST

FBIAS ADJUST

AG Set (MO)

AG Set (CD)

TEMP CHECK

LDPWR CHECK

EF MO CHECK

EF CD CHECK

FBIAS CHECK

ScurveCHECK

VERIFYMODE

DETRK CHECK

0920 CHECK

Iop Read

Iop Compare

ADJ CLEAR

INFORMATION

CPLAY 2MODE

CREC 2MODE

Details

Automatic self-diagnosis

Error history display, clear

Temperature compensation offset adjustment

Laser power adjustment

Iop data writing

Writes current Iop value in read nonvolatile memory using microprocessor

Traverse (MO) adjustment

Traverse (CD) adjustment

Focus bias adjustment

Auto gain output level adjustment (MO)

Auto gain output level adjustment (CD)

Temperature compensation offset check

Laser power check

Traverse (MO) check

Traverse (CD) check

Focus bias check

S-curve check

Nonvolatile memory check

Detrack check

Most circumference check

Iop data display

Comparison with initial Iop value written in nonvolatile memory

Initialization of nonvolatile memory for adjustment values

Display of microprocessor version, etc.

Continuous playback mode

Continuous recording mode

No.

C01

C02

C03

C04

C05

C06

C07

C08

C09

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C25

C26

C27

C28

C31

C36

C37

Mark

Group

Check

Service

“CPLAY 2MID”

“CPLAY 2OUT”

“CPLAY 2IN”

Содержание MDS-SE9














































































Результаты поиска

Содержание MDS-SE9

Отзывы:

Похожие инструкции для MDS-SE9

Бренды по названию

Популярные бренды

Sony MDS-SE9, Руководство по обслуживанию

Результаты поиска

Содержание MDS-SE9

Отзывы:

Похожие инструкции для MDS-SE9

Бренды по названию

Популярные бренды