13
Location and Function of Parts
d
SWITCHER DATA connector (RJ-45)
Connect to an Ethernet switch.
The DVS-9000 System is connected in the same way to the
Ethernet switch to form a network for exchange of signals
between the devices. This network is used primarily for
exchange of various types of data (key frame effects,
snapshots, etc.) and still pictures of frame memory.
Caution
When using a LAN cable: For safety, do not connect to a
connector for peripheral device wiring that might have
excessive voltage.
e
REF IN (reference signal input) connectors (BNC
type)
If you wish to synchronize this unit to an external reference
signal, input a black burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75
Ω
terminator.
f
DME EXT IN (Digital Multi Effects External
input) 1 to 4 connectors (BNC type) (BKDS-9470)
Connectors for four serial digital video signal inputs.
Dedicated input for DME external video.
g
DME DATA (Digital Multi Effects Data) connector
(RJ-45) (BKDS-9470)
Connect to an Ethernet switch.
The DVS-9000 System is connected in the same way to the
Ethernet switch to form a network for exchange of signals
between the devices.
Caution
When using a LAN cable: For safety, do not connect to a
connector for peripheral device wiring that might have
excessive voltage.
h
DME CTRL (Digital Multi Effects Control)
connector (RJ-45) (BKDS-9470)
Connect to an Ethernet switch.
The DVS-9000 System is connected in the same way to the
Ethernet switch to form a network for exchange of signals
between the devices.
This network is used primarily to control the various
devices from the center control panel.
Caution
When using a LAN cable: For safety, do not connect to a
connector for peripheral device wiring that might have
excessive voltage.
i
DME MONI OUT (Digital Multi Effects Monitor
Output) 1 to 4 connectors (BNC type) (BKDS-9470)
Connectors for four serial digital video signal outputs.
These connectors allow you to monitor any desired output
signal with the DME signal (video, key, or with graphics).
j
DME REMOTE (Digital Multi Effects Remote)
connector (D-sub 9-pin, RS-422A) (BKDS-9470)
When a BKDS-9470 DME Board Set is installed, use this
connector to control the unit from an external device.
k
DME GPI (Digital Multi Effects General Purpose
Interface) connector (D-sub 25-pin) (BKDS-9470)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
with input and output conditions set on the center control
panel.
l
SWITCHER GPI (Switcher General Puropose
Interface) connector (D-sub 25-pin)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
with input and output conditions set on the center control
panel.
m
SWITCHER REMOTE 1 to 4 connectors
(D-sub 9-pin, RS-422A)
Used to control the DVS-9000SF AUX bus from external
devices, and to operate the DVS-9000SF from editing
control systems such as the BVE-9100.
Specify the types of connected devices on the center
control panel.
n
TERMINAL connector (D-sub 9-pin, RS-232C)
This connetor is used for factory adjustments.
o
U
(signal ground) terminal
Connect to the system ground.
p
-
AC IN (AC power input) A, B connectors (3-pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cords.
Depending on the system’s configuration when shipped,
there may be no optional HK-PSU04 Power Supply Unit
installed. In that case, the AC IN B connector is not used.
Caution
For information about installing an HK-PSU04, contact
your Sony service representative.
q
PRIMARY INPUTS 1 to 34 connectors (BNC type)
(MKS-8110SD)
These connector accept up to 34 serial digital video signal
inputs. The number of connectors varies depending on the
number of MKS-8110SD boards installed.
Содержание HK-PSU04
Страница 22: ...22 Specifications ...
