10
Overview
Parts Identification
Front panel
a
Camera Control Unit (CCU) connector (optical fiber
connector)
Connect an HDCU1000 Camera Control Unit with an HKCU-
HB10 3G Fiber Transmission Unit mounted or HDCU1500 with
an HKCU-HB15 mounted, using an optical fiber cable.
A single optical fiber cable enables transmission of power,
control signals, video signals, and audio signals between two
cameras and an HDCU1000/1500.
b
Cable clamp belt attachment screw holes
Attach the cable clamp belt (supplied) to secure the optical
fiber cable.
Rear panel
SY type: Models for JN and SY
a
INTERCOM connector (XLR 5-pin)
Connect an XLR 5-pin headset for input and output of intercom
audio signals.
The connector can be used for communication over the
engineer line when the camera is in standby status.
b
PGM1 (Program 1) knob
To adjust the audio listening level of program 1.
c
PGM2 (Program 2) knob
To adjust the audio listening level of program 2.
d
RET 1 (return video 1) button
The return video 1 signal is displayed on the viewfinder screen
while the button is held pressed.
e
RET (return video) button and 2/3/4 (return video 2/3/4)
select switch
When other return video systems are used in addition to return
video 1, the signal selected with the 2/3/4 select switch is
displayed on the viewfinder screen while holding the RET
button pressed.
The RET 1 button has priority over the RET (2/3/4) button if
both buttons are pressed.
f
“Memory Stick Duo” slot and access lamp
When you insert a “Memory Stick” into the slot, the access
lamp lights in green.
The lamp is lit in red while writing/reading data to/from the
“Memory Stick.”
• Only a “Memory Stick” of Duo size can be used with the
camera.
• When the access lamp is lit in red, do not insert/remove the
“Memory Stick Duo” or turn off the camera.
For details on “Memory Stick”, see “Using a “Memory Stick””
(page 35).
g
CAMERA POWER switch and indicator
CCU:
To operate on power supply via the connected CCU.
OFF:
Not to supply power.
EXT:
To operate on power supply through the DC IN
connector.
The indicator is lit in green during operation. It is lit in red while
standby power is being supplied from the CCU, even if the
switch is set to OFF.
If the unit is connected to a CCU with the switch set to EXT for
power being supplied through the DC IN connector, the
CABLE ALARM (OPEN) indicator on the CCU may light, but
the unit and CCU can be used.
h
CALL button
Press to call the operator of the external control device (RCP,
etc.). The call lamp of the connected device will light.
i
Line select switch
To select the intercom line:
PROD:
Producer line
ENG:
Engineer line
j
MIC (microphone) switch
Turns ON and OFF the microphone of the intercom headset.
ON:
To turn on the microphone.
OFF:
To turn off the microphone.
PTT:
To turn on the microphone while the switch is set to this
position. The switch is not locked at this position.
k
INTERCOM level control
To adjust the intercom audio listening level.
l
DISPLAY switch
Select the display on the viewfinder screen.
ON:
To display various textual information, such as messages
showing the camera settings and operating status, in
addition to camera images.
OFF:
To display camera images only.
1
2
8
9 0 qa
qs
qd
qf
qg
1
2 3 4
5
6
7
INTERCOM
CAMERA POWER
INTERCOM
CALL
PRO Duo
DISPLAY
ASSIGNABLE
PROD
ENG
PGM2
VF SOURCE
MIC
ON
BOTH
MIX SPLIT DIFF
CAM HD PROMPT
L
R
OFF
EXT
OFF
CCU
PTT
ON
OFF
MENU
PGM1
RET1
RET
2 3 4
Note
Notes
Note
