![background image](http://html.mh-extra.com/html/sony/hcd-vx8/hcd-vx8_service-manual_420912002.webp)
– 2 –
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output four times.
4-215-641-0
π
VX8: EA
MALAYSIA
4-215-641-1
π
VX8: MY, SP
MALAYSIA
4-215-641-2
π
VX8: TW
MALAYSIA
4-215-641-3
π
VX8: E
MALAYSIA
4-215-641-4
π
VX8: IA
INDONESIA
4-215-641-5
π
VX8: HK
MALAYSIA
4-215-641-6
π
VX8J: E
JAPAN
4-215-641-7
π
VX8J: EA
JAPAN
4-215-641-8
π
VX8: TH
THAI
MODEL IDENTIFICATION
— BACK PANEL —
• Abbreviation
EA
: Saudi Arabia model
TW
: Taiwan model
IA
: Indonesia model
HK
: Hong Kong model
TH
: Thai model
MY
: Malaysia model
SP
: Singapore model
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE
WITH MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER PROD-
UCT MARKING is located on
the rear exterior.
Parts No.
PARTS No.
MODEL
PRODUCT
COUNTRY
Содержание HCD-VX8
Страница 6: ... 6 This section is extracted from instruction manual ...
Страница 26: ...HCD VX8 VX8J 8 3 PRINTED WIRING BOARD CD SECTION See page 18 for Circuit Boards Location 33 34 Page 42 ...
Страница 28: ...HCD VX8 VX8J 8 5 SCHEMATIC DIAGRAM DECK SECTION 37 38 Page 55 ...
Страница 46: ...HCD VX8 VX8J 8 24 SCHEMATIC DIAGRAM TRANS SECTION 73 74 Page 54 Page 57 ...