1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-UX3E/UX5/UX5E/UX7/UX7E_L2
1-5-3. Self-diagnosis Code Table
C
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
3
2
2
0
3
1
6
1
6
1
6
2
6
2
6
2
6
2
6
2
6
2
6
2
6
2
9
1
9
4
Detailed
Code
0
0
0
1
0
2
0
0
6
0
0
0
0
0
1
0
1
1
0
0
0
1
0
2
0
3
1
0
1
1
1
2
2
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
Disc access error
Condensation.
Difficult to adjust focus
(Cannot initialize focus)
EEPROM data are rewritten.
Drive fault
Zoom operations fault
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
communication abnormality among.
Shift lens initializing failure.
Shift lens overheating (Pitch).
Shift lens overheating (Yaw).
Abnormality of thermistor.
Abnormality when flash is being charged.
Fault of writing to or erasing the
flashmemory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin
ql
,
wa
of
CN5302 on the LD-215 board: UX3E/UX5/UX5E, pin
qh
,
qk
of
CN5302 on the LD-216 board: UX7/UX7E). If it is OK, check
the focus motor drive IC (IC5404 on the LD-215 board: UX3E/
UX5/UX5E, IC5404 on the LD-216 board: UX7/UX7E).
Make EEPROM data correct value.
Inspect or replacement of the mechanism deck, IC (IC4401 on
the MD-134 board) and drive block.
Inspect the lens block zoom MR sensor (pin
qh
,
qk
of CN5302
on the LD-215 board: UX3E/UX5/UX5E, pin
w;
,
wa
of CN5302
on the LD-216 board: UX7/UX7E) when zooming is performed
when the zoom lever is operated, and the zoom motor drive
circuit (IC5404 on the LD-215 board: UX3E/UX5/UX5E,
IC5404 on the LD-216 board: UX7/UX7E) when zooming is not
performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE8202 on the CM-076
board: UX3E/UX5/UX5E, SE7202 on the CM-077 board: UX7/
UX7E) peripheral circuits.
Inspect YAW angular velocity sensors (SE8201 on the CM-076
board: UX3E/UX5/UX5E, SE7201 on the CM-077 board: UX7/
UX7E) peripheral circuits.
Refer to [1-6-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred] (UX7/UX7E only).
Inspect the steadyshot circuit (IC5703 on the LD-216 board)
(UX7/UX7E only).
UX7/UX7E only:
1. Inspect the EEPROM (IC1840 on the VC-487).
2. Perform the STEADY HALL adjustment. (Note 1)
3. Replace the lens block. (Note 2)
Refer to [1-6-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred] (UX7/UX7E only).
Refer to [1-6-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred] (UX7/UX7E only).
Refer to [1-6-4. E : 62 : 20 (Abnormality of Thermistor)
Occurred] (UX7/UX7E only).
Checking of flash unit or replacement of flash unit.
Inspect the flash memory (IC4302 on the MD-134 board).
Note 1: Perform adjustment by referring to “STEADY HALL Adjustment” in Service Manual, ADJ. After the adjustment, be sure
to perform “GYRO Sensor Sensitivity Adjustment”.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
