Sony Exmor HXCU-D70, Руководство по эксплуатации

Страница: 12 / 36

12
Locations and Functions of Parts
Rear Panel
a
“Memory Stick” slot
For service use only.
b
LAN jack (RJ-45, 8-pin)
Connects to a LAN hub (10BASE-T/100BASE-TX), when
using a network connection, via a LAN cable (shielded type,
category 5 or higher).
• For safety, do not connect the connector for peripheral device wiring
that might have excessive voltage to this port. Follow the
instructions for this port.
• When you connect the LAN cable of the unit to peripheral device,
use a shielded-type cable to prevent malfunction due to radiation
noise.
Par mesure de sécurité, ne raccordez pas le connecteur pour le
câblage de périphériques pouvant avoir une tension excessive à ce
port. Suivez les instructions pour ce port.
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-Anschluss
verbinden, der zu starke Spannung für diese Buchse haben könnte.
Folgen Sie den Anweisungen für diese Buchse.
c
REMOTE connector (8-pin)
Transmits and receives control signals from the RCP-1000-
series Remote Control Panel via a CCA-5 cable (optional). It
also supplies power when connected to an RCP-1000-series
Remote Control Panel.
d
Pr/R/R-Y, Y/G/Y, Pb/B/B-Y (component signals)
connectors (BNC type)
Outputs the HD component signals, SD component signals,
HD RGB signals, or SD RGB signals from the corresponding
connectors.
e
VBS RETURN 1, 2 (VBS return video 1, 2) connectors
(BNC type)
IN : Inputs the VBS return video signals (2-system).
OUT : The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75
Ω
terminator.
f
AUDIO OUTPUT CH-1, CH-2 connectors (XLR 3-pin)
Outputs audio signals from the camera AUDIO 1 IN and
AUDIO 2 IN connectors.
g
CAMERA connector (multi-core connector)
Connects to the camera via a multi-core cable. The camera
sends all video and audio signals to the CCU, and the CCU
sends control signals, return video, audio signals and power to
the camera over a single multi-core cable.
CAMERA connector is non LPS (Limited Power Source) circuit. This
connector is connected to the HXC-D70.
h
AC supply input connector
Connects to the AC supply via the specified power cord
(optional). A plug holder (optional) can be used to secure the
power cord to the CCU.
i
REFERENCE (reference input) connectors (BNC type)
IN : Inputs an HD tri-level reference sync signal or SD
reference sync signal (black burst signal) for external sync.
OUT : The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75
Ω
terminator.
j
PROMPTER (teleprompter input) connectors
(BNC type)
IN : Inputs the VBS signal for the teleprompter.
OUT : The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75
Ω
terminator.
k
S-VIDEO OUTPUT connector (4-pin)
Outputs S-VIDEO signal.
l
HDMI OUTPUT connector (19-pin)
Outputs HDMI signal for a video monitor compatible with HDMI
input.
• When connecting a household television with HDMI input, set its
high-resolution function to off to avoid image artifacts.
• Use a Sony high-speed HDMI cable.
m
VBS 1, 2 (composite video signal 1, 2) connectors
(BNC type)
Outputs (2-system) the camera signals in composite signal
format.
n
SDI OUTPUT 1 to 4 connectors (BNC type)
Outputs the camera signals in HD SDI or SD SDI signal
format.
The SDI OUTPUT 3 and SDI OUTPUT 4 connectors can also
output signals with superimposed character or marker display.
SDI OUTPUT
REFERENCE PROMPTER
S-VIDEO
OUTPUT
HDMI
OUTPUT
SYNC PIX VBS2 VBS1
Pb/B/B-Y Y/G/Y Pr/R/R-Y REMOTE
AUDIO OUTPUT
INTERCOM/TALLY/PGM TRUNK
VBS RETURN
CH-1
1
1 2 3 4
2
IN IN
OUT OUT
CH-2
IN IN
OUT OUT
PRO
CAMERA
~ AC IN
a
ij m l k no p q
r
b
c d
e
f h g
CAUTION
ATTENTION
VORSICHT
CAUTION
Notes