Sony DXC-D35, Руководство по обслуживанию

Страница: 29 / 122

1-21
DXC-D35/D35WS(UC) DXC-D35P/D35WSP(CE) V1
Chapter 2 Fitting and Connections
40
Chapter 2 Fitting and Connections
Power Supply
This unit operates on either a battery pack or an AC
supply (using the optional CMA-8A/8ACE AC
Adaptor).
For details of the power supplies which can be used, refer to
the documentation supplied with the VTR connected to this
unit or the camera adaptor.
Using an Anton Bauer Intelligent Battery
System and Ultralight System
Fitting the special battery mount made by Anton Bauer
Corporation to this unit allows you to use their
Intelligent Battery System and Ultralight System.
For details, consult your Anton Bauer products supplier or
Sony dealer.
Using Battery Packs
Always fully charge a battery pack before using it.
Notes
• Be careful that other metal objects do not come in
contact with the metal parts of the battery pack, as
this could cause a short.
• Do not leave the battery pack in the camera if it is not
going to be used for a long time.
• If the battery pack is recharged after use while still
hot, it may not be possible to obtain a full charge.
Fitting a battery pack (NP-1B)
Open the lid of the battery case, insert a fully-charged
battery pack, and close the lid.
Battery pack operating times
The following table shows approximate continuous
operating times, when operating the camera and 1.5-
inch viewfinder at normal temperatures, with a camera
adaptor and an DSR-1/1P or PVV-3/3P connected.
Approximate operating times with
a fully-charged battery pack
DXC-D35/D35P
DXC-35WSL/D35WSPL
a) Requires the special-purpose DC-500 Battery Case.
Cannot be used with a camera adaptor.
Battery low indications
When the voltage of the supply to the camera head
lowers to or below 11.0 V, the battery voltage
indication appears in the viewfinder. At this time, the
BATT indicator in the viewfinder flashes when
operating with the DSR-1/1P or PVV-3/3P.
If you continue using the camera head, the BATT
indicator lights up.
When the battery pack is low, replace it with a fully-
charged battery pack.
Press and lift
Battery case
NP-1B Battery
Pack
With DSR-1/
1P With camera
adaptor Battery pack With PVV-3/
3P
NP-1B 110 minutes 60 minutes 60 minutes
NP-1A 85 minutes 45 minutes 50 minutes
BP-90A
a)
— 130 minutes 140 minutes
Battery pack With camera
adaptor With DSR-1/1P or
PVV-3/3P
NP-1B 95 minutes 50 minutes
NP-1A 70 minutes 35 minutes
BP-90A a) – 105 minutes
Chapter 2 Fitting and Connections
Chapter 2 Fitting and Connections
41
Battery pack charging
Before using a battery pack, charge it as shown in the
following table.
For details of battery charger operation, refer to the
instructions provided with the battery charger to be used.
Camera Adaptor Power Supply
The camera adaptor automatically operates on power
supplied to the VTR/CCU/CMA connector from the
portable VTR, CCU-M7/M7P Camera Control Unit,
CMA-8A/8ACE AC Adaptor or other connected
device.
Note
Before use, check that the device connected to the
VTR/CCU/CMA connector is able to provide the
power required by the camera.
If it is not able to provide the necessary power, or
when it is necessary to prolong the operating time, use
the camera with a separate power supply.
Approximate
charging time
(normal temperature) Battery charger Battery pack
NP-1A BC-1WD/1WDCE,
BC-410/410CE 70 minutes
NP-1B BC-1WD/1WDCE,
BC-410/410CE 95 minutes
BP-90A BC-410/410CE 160 minutes