Sony DVCAM DSR-25, Руководство по обслуживанию

Страница: 171 / 238

5-46
DSR-25
3-2. SYSTEM CONTROL SYSTEM
ADJUSTMENTS
1. Initializing the C, D, E Page Data
Note 1: If “Initializing the C, D, E Page Data” is performed, all
data of the C page, D page and E page will be initialized.
Note 2:
If the C, D, E page data has been initialized, “Modifica-
tion of C, D, E page Data” and all adjustments need to be
performed again.
Mode E-E
Signal Arbitrary
Adjustment Page C
Adjustment Address 00 to DF
Adjustment Page D
Adjustment Address 10 to 3F
Adjustment Page E
Adjustment Address 10 to ED
4. Input of E Page Initial Data
Note 1:
Perform the operation after setting the DISPLAY SE-
LECT switch on the front panel to any mode other than
“MENU”.
Note 2:
When EEPROM (IC708 on VD-032 board) is replaced
with a brand-new one, apply power with the following
method before operation.
1) Connect the adjustment remote commander without
connecting the cable to AC connector.
2) Set the HOLD switch on the adjustment (adjusting)
remote commander to “HOLD” (service position).
3) Connect the cable to AC connector.
Input method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 9, address: 00, set data: 2D, and press the PAUSE
button on the adjustment remote commander.
3) Select page: 9, address: 01, set data: 2D, and press the PAUSE
button.
4) Select page: 9, address: 02, and check that the data change to
“01”.
5) Press the RESET switch at the bottom of the set using a thin
and long pin.
6) Disconnect the adjustment remote commander, and turn the
POWER switch OFF.
7) Disconnect the cable connected to AC connector once, then
connect them again.
8) Turn the POWER switch ON.
9) Modify the E page data. (Refer to E page table)
5. Modification of C, D, E, Page Data
If the C, D, E page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note : If copy the data built in the different model, this set may
not operate.
3) When changing the data, press the PAUSE button of the ad-
justing remote commander each time when setting new data
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
5) After completing “Modification of C, D, E Page Data”, select
page: 0, address: 01, and set data: 00. Also perform all adjust-
ments.
2. Input of C Page Initial Data
Input method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 80, set data: 0C, and press the PAUSE
button on the adjustment remote commander.
3) Select page: 3, address: 80, and check that the data change to
“1C”.
4) Press the RESET switch at the bottom of the set using a thin
and long pin.
5) Modify the C page data. (Refer to C page table)
3. Input of D Page Initial Data
Input method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 80, set data: 0D, and press the PAUSE
button on the adjustment remote commander.
3) Select page: 3, address: 80, and check that the data change to
“1D”.
4) Press the RESET switch at the bottom of the set using a thin
and long pin.
5) Modify the D page data. (Refer to D page table)