1-3
33
English
4
VIDEO OUT connector section
Three sets of video outputs. The converted signal is
output from this section.
Y/C output (4-pin):
Connect to the Y/C input of video equipment.
Only the NTSC or PAL signal is output from this
connector.
Composite video output (BNC type):
Connect to the composite video input of video equipment.
Only the NTSC or PAL signal is output from this
connector.
RGB/component output (D-sub 15-pin, 3-row):
Connect to the RGB or component (Y/B-Y/R-Y) inputs of
video equipment.
RGB/YBR output selector:
Set this selector depending on the format of the signal
output from the D-sub connector. YBR is effective when the
NTSC or PAL signal is output.
SYNC output selector:
Select the sync signal for the RGB output.
Set to SEP to use separate horizontal/vertical sync signal.
Set to COMP to use the composite sync signal.
5
AUDIO IN L/R jacks (RCA pin)
Three sets of audio inputs.
Connect to the audio output jacks of equipment. If the
input source is monaural, connect it to the L jack only.
You can select the audio input with the INPUT SELECT
buttons on the front panel.
6
AUDIO OUT L/R jacks (RCA pin)
A set of audio outputs.
Connect to the audio input jacks of equipment.
AC IN
CTRL S
AUDIO IN
OUT
VIDEO OUT
IN
OUT
L
R
L
R
L
R
L
R
AUDIO 1
AUDIO 2
AUDIO 3
RGB
YBR
SEP
COMP
SYNC
VIDEO 3 IN
THROUGH
RGB
YBR
75
OPEN
AUTO
ON G
SYNC
VIDEO 2 IN
VIDEO 1 IN
Y/C
IN OUT
COMP
IN OUT
4
5
6 7
8
THROUGH
NORMAL
COMP
75
OPEN
RGB
YBR
REF
7
CTRL S IN/OUT jacks (minijack)
Connect to the CONTROL S jacks of other Sony equipment.
It is then possible to control the whole system with a single
remote commander.
When a plug is connected to the CTRL S IN jack, the
remote sensor on the front panel becomes inactive.
8
AC IN connector
Connect the supplied power cord.
34
Before you get started
• First make sure that the power to each piece of equipment is
turned off.
• Use connecting cables suitable for the equipment to be
connected.
• The cable connectors should be fully inserted into the jacks.
A loose connection may cause hum and other noise.
• To disconnect the cable, pull out by grasping the plug.
Never pull the cable itself.
• Read the instruction manual of the equipment to be
connected.
Hookups
Hookup for getting the up-converted signal
The following diagram shows a connection example to convert a low-rate input signal into a high-rate output signal.
Setting the VIDEO OUT selectors
• Set the RGB/YBR selector to RGB (when a computer
monitor, data projector or LCD projector is connected).
•
Set the SYNC selector to SEP (HD or VD separate sync) or
COMP (composite sync) depending on the connected
equipment.
When the Betacam SP video cassette recorder is
connected to VIDEO 3 IN
Set the VIDEO 3 IN selectors as follows:
•
75
/OPEN selector
m
75
•
RGB/YBR selector
m
YBR
•
SYNC selector
m
AUTO
Connect only the three plugs of the signal cable to the Betacam
SP video cassette recorder: green plug to Y connector, red to R-
Y, and blue to B-Y. Leave the other plugs, if provided,
disconnected.
VIDEO 3 IN
VCR, laser disc player,
game machine, etc.
S VIDEO
OUT
AUDIO OUT L/R
AC power cord
VIDEO OUT
to a wall outlet
Betacam SP video cassette
recorder
Signal cable (supplied)
Data projector, LCD projector,
etc.
VIDEO 3 IN selectors
VIDEO 1 IN
Y/C IN
AC IN
Computer monitor (VGA or SVGA),
etc.
CONTROL
S OUT
AUDIO
OUT L/R
COMPONENT
(Y, R-Y, B-Y)
AUDIO IN
AUDIO 1 L/R
AUDIO IN
AUDIO 3
L/R
CTRL S IN
OUT L/R
AUDIO IN
L/R
Public announcement
system, etc
R/G/B/HD/VD IN
VIDEO OUT selectors
AC IN
CTRL S
AUDIO IN
OUT
VIDEO OUT
IN
OUT
L
R
L
R
L
R
L
R
AUDIO 1
AUDIO 2
AUDIO 3
RGB
YBR
SEP
COMP
SYNC
VIDEO 3 IN
THROUGH
RGB
YBR
75
OPEN
AUTO
ON G
SYNC
VIDEO 2 IN
VIDEO 1 IN
Y/C
IN OUT
COMP
IN OUT
THROUGH
NORMAL
COMP
75
OPEN
RGB
YBR
REF
Содержание DSC-1024HD
Страница 20: ...DSC 1024HD 3 5 MEMO ...
Страница 43: ...DSC 1024HD MEMO 5 3 ...
