78
Chapter 3 Menu
Chapter 3 Menu
Menu Windows
A
Automation return mode button
Touch this button to select the mode that returns to the
previous data.
BUTT:
Returns to the previous data as a “jump” at the
DROP OUT.
RAMP:
Ramps back to the previous position after the
DROP OUT.
HOLD TO NEXT:
Holds the setting at the DROP
OUT point until the next automation move is replayed.
HOLD TO END:
Holds the setting at the DROP OUT
point to the end of the data.
TOP TO END:
Holds the setting at the DROP OUT
point from the top of the timecode (00:00:00:00) to the
end of the data.
B
RAMP frame display
Sets the time to return to the position stored in the
previous data in unit of frame.
By touching the display, you can set the desired return
time using the ten key pad. The displayed values can
be increased or decreased using the +/– keys and the
jog dial on the panel.
4
PUNCH IN/OUT section
This section allows you to punch in and out of
dynamic automation WRITE by sending an ON/OFF
signal or specifying the timecode.
FOOT SW button:
Touch this button to active the
foot switch automation WRITE control. When this
button is not selected, the foot switch status is ignored.
AUDITION button:
When you touch this button, the
following items are automatically set as below.
WRITE HOLD and TOUCH HOLD modes
t
ON.
SAFE button on the panel
t
ON.
Auto return mode
t
BUTT.
In this mode, the automation data is overwritten only
while the SAFE button is OFF.
Notes
• In AUDITION mode, the SAFE button controls
storing of the automation data; When the button is
OFF the data is stored, and when the button is ON the
data is not stored. Therefore, in this mode, the
previous data is not protected even when you set the
SAFE button to ON before stopping the tape.
• The items cannot be dropped out (cancels WRITE)
automatically even when the AUDITION mode is
cancelled. Drop out them using a manual operation.
For the use of the AUDITION mode, see page 114.
AUTO button:
Touch this button to enable the
PUNCH IN TIME/PUNCH OUT TIME display
windows. When this button is not selected, automation
data is stored regardless of the values in the PUNCH
IN/OUT TIME windows.
PUNCH IN TIME button and display window:
Touch this button to accept the time displayed on the
timecode display window on the Automation panel.
This time is then displayed in the windows.
You can enter the timecode using the ten keys by
touching the timecode on the display window.
Remember to press the ENTER button to accept this
value.
You can increase or decrease the numeric values using
the + / - buttons and the jog dial.
PUNCH OUT TIME button and display window:
Touch this button to accept the time displayed on the
timecode display window on the Automation panel.
This time is then displayed in the window.
You can enter the timecode using the ten keys by
touching the timecode on the display window.
Remember to press the ENTER button to accept this
value.
You can increase or decrease the numeric values using
the + / - buttons and the jog dial.
WRITE NOW button:
Touch this button to write the
automation data between punch-in and punch-out
durations without running the tape.
To change the data between punch-in and
punch-out duration
1
Stop the timecode feed, eg stop a MT machine.
2
Touch the AUTO button on the window.
3
Specify the punching in and out points.
4
Set the automation mode to ABS or TRIM.
5
Set the item to be adjusted to READY.
6
Drop in the adjusted item.
7
Adjust the item in step 5 to the proper level.
Содержание DMX-R100
