DSC-HX20/HX20V/HX30/HX30V_L2
2-7
2-1-5. LENS BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
#189
#189
#258
ns
ns
ns
ns
208
210
209
205
206
207
204
203
202
211
201
(Note 1, 2
, 5
)
212
(including CD-840 flexible complete board,
CP001 (CMOS imager))
(Note 3)
ns
ns
ns
213
(Size: 16mm X 40mm)
(Note 4)
1. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇
-X
: Solder
DISASSEMBLY
Screw
#189: M1.4 X 3.5 (Tapping)
(Silver)
3-686-458-21
3.5
1.4
#258: M1.4 X 3.5 (Tapping)
(Silver)
4-299-468-11
1.2
3.5
Note
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Zoom Motor
Very weak
Focus Motor
Very weak
Focus Lens
Very weak
Sensor
Very week
Lens Barrier
Very weak
Ornamental Ring
Flexible
Board
Note 2:
Refer to the following each item when you exchange parts of Lens Block.
• 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD (page 1-12)
• 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD (page 1-12)
• 1-11. CAM TUBE (B) ASSY REPLACING METHOD (page 1-13)
• 1-12. FINAL INSPECTION (page 1-19)
Note 2:
レンズブロックの各部品を交換する際は，下記の各項目を参照してください。
• 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
(page 1-12)
• 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD (page 1-12)
• 1-11. CAM TUBE (B) ASSY REPLACING METHOD (page 1-13)
• 1-12. FINAL INSPECTION (page 1-19)
Note 3:
Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 3:
イメージャの交換時は
Level3
の
6-1
ページ、
“
イメージャ
交換時の注意
”
を必ずお読みください。
209
4-424-722-01
TUBE, FEED-THROUGH CAM
210
4-424-720-01 GEAR,
NARUTO
211
1-490-422-11
GEAR BLOCK, ZOOM MOTOR (BE017)
212
A-1870-790-A CD-840 FLEXIBLE BOARD, COMPLETE
(including CP001 (CMOS imager)) (Note 3)
213
2-580-751-01
SHEET, POLYIMIDE (Note 4)
#189 3-686-458-21 SCREW
(P1.4),
TAPPING
#258 4-299-468-11 SCREW,
TAPPING
UB1.2
201
1-856-265-11
OPTICAL UNIT (BE017) (Note 1, 2
, 5
)
202
4-424-721-01
RING (A), ORNAMENTAL
203
X-2584-294-1 BARRIER
ASSY
204
X-2584-295-1 TUBE (A) ASSY, STRAIGHT
205
4-424-723-01
TUBE (A), CAM
206
X-2584-297-1 TUBE (B) ASSY, CAM
207
4-424-724-01
TUBE (B), STRAIGHT
208
X-2584-296-1 TUBE
ASSY,
ROTARY
Note 4:
Cut SHEET, POLYIMIDE (2-580-751-01) into the
designed length and use it.
Note 4:
SHEET
、
POLYIMIDE
（
2-580-751-01
）は切って使用し
てください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note 5:
When this part is removed, adjustment is required.
For the adjustment method, refer to “Adjustment items
after replacing parts” in the Note tab of the Adjust manual.
Note 5:
この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにあ
るAdjustment items after replacing parts を参照して
ください。
