36
Audio Equipment Selection
Adapter
DWA-01D Wireless Adapter
The DWA-01D can be used as a portable wireless receiver in
conjunction with the Digital Wireless Receiver DWR-S01D. It can
also be mounted on a camcorder, and two units can be linked
for 4-channel operation.
Audio output can be switched to analog or AES/EBU digital
output. AES/EBU digital output carries two channels over a
single cable. Channel 1 can be analog, even if channel 2
is used as digital output. (Analog UHF Synthesizer Tuner Unit
WRR-855S is also supported, but the AES/EBU digital output and
analog output in channel 2 cannot be used.)
Front
Monitor output selector
Selects the audio output from the PHONES connector.
1:
Outputs the audio from the OUTPUT1 connector to the L/R
channels.
1+2:
The audio from the OUTPUT1 connector is mixed with the
audio from the OUTPUT2 connector (only when the OUTPUT2
connector is set to output analog signal) and output to the L/R
channels.
2:
Outputs the audio from the OUTPUT2 connector (only when
the OUTPUT2 connector is set to output analog signal) to the L/R
channels. When the WRR-855 is attached, no audio is output
from the PHONES connector.
Note
Monitor output is split from the analog signal output to the
OUTPUT1/2 connectors. When audio that is output to the
OUTPUT1 connector is changed on the DWR-S01D using
the ANALOG OUTPUT1 function, monitor output changes
accordingly.
PHONES (monitor output)
connector (3.5 mm, TRS jack, tip: L, ring: R, sleeve: ground)
Connect the headphones here. Select the output signal using
the monitor output selector.
Monitor level control
Adjusts the monitor output level.
Bottom
DC IN (external power input)
connector (4-pin) Connect to the external power output
connector of the camcorder using the supplied DC power cable.
This connector accepts the power voltage between 10 V DC and
17 V DC.
WORD SYNC (word sync input) connector (BNC type)
Accepts external sync signal. When the DWR-S01D is attached
and the sync signal is input, the DWR-S01D can be operated in
synchronization with the whole audio system.
Note that this connector does not work when the WRR-855S is
attached.
Note
Even when the 75-ohm termination has been added on the
DWR-S01D, this connector still works as the high-impedance input
connector while the DWR-S01D is turned off.
OUTPUT1 (analog audio output) connector (4-pin)
Outputs balanced analog audio signal. When the DWR-S01D is
attached, audio from the tuner 1 or 2 can be selected by
using the UTILITY menu of the DWR-S01D. The output from this
connector is factory-set to the audio from the tuner 1. When the
WRR-855S is attached, audio is output from this connector only.
OUTPUT2 (analog/digital audio output) connector (4-pin)
When the DWR-S01D is attached, this connector outputs
balanced analog audio signal or AES3-format digital audio
signal. Output signal can be selected using the ANALOG AES/
EBU selector. When this selector is set to ANALOG, audio from the
tuner 2 is output.
Note that this connector does not work when the WRR-855S is
attached.
ANALOG AES/EBU selector
When the DWR-S01D is attached, this selector determines the
signal output from the OUTPUT2 connector.
ANALOG:
Balanced analog audio signal is output.
AES/EBU:
AES3-format digital audio signal is output.
Note that this selector does not work when the WRR-855S is
attached.
Note
DWA-01D supplied accessories include two xx inch length XLR
adapter cables for the purpose of audio output connection with
output 1 and output 2.
Syste
U
In orde
describ
System
BNC c
Configuring a DWX System
