manualshive.com logo in svg

Sony BKS-R1617, Руководство по эксплуатации

Поделиться
Скачать
Sony BKS-R1617 Скачать руководство пользователя страница 19

19

Error Messages

While trouble occurs on this unit, the following error
messages appear in the preset display window.

Error messages

Contents

Remarks

PacE

Reception error on the S-BUS data link

If this occurs only once every several minutes, it is not a
problem.  Power source noise or an S-BUS remote cable
longer than 500 m using BELDEN cable or equivalent may be
the cause.  If the same errors still occurs on this unit when
used under conditions without the above causes, the trouble
may be in this unit.

RstP

The primary station has been reset.

This occurs when the primary station is turned on, or when
some trouble occurs in the S-BUS data link.

Scrt

A source set as secret is to be selected.

A source set as secret cannot be selected on a unit other than
the primary station.

ComE

Communication error of the S-BUS data

This may occur when the communication period is too long.

link

The primary station may be turned off, or the remote cable may
be disconnected.

Prot

The destination is protected.

The protected destination cannot be switched.  In the preset
display window, ID of the station which has set the protection
to the destination, is displayed.

NotF

The name cannot be found

The designated type name for type-number selection does not
exist in the table.

LvlE

All levels are not controllable.

All levels are set not to be controlled.

NoDt

The destination has not been set.

The designated destination has not been set.  Change the
selection or setting.

NotA

The source is out of the available souces. The source to be swithed is not found within the range of the

available sources.  The source cannot be changed.

Содержание BKS-R1617























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды