Sony Ericsson Developer's Board Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

Sony Ericsson Developer's Board Скачать руководство пользователя страница 9

Developer's Board Manual Rev A

Page 9 of 28

SEM/CX-02:0061/MAN

Figure 3: Exploded view drawing of developer's board with CM-4x

Assembly instructions:

•

Place Thermal pad on center of heat sink, making sure to align screw holes.

•

Attach module to standoff and heat sink using 5/16" screws in eight positions. Six are placed along the

perimeter of the board, the remaining two are under the hexagon shield can.

•

Attach 40-conductor to 40-conductor ribbon cable to JP2 and the module.

Note

: Components under shield cans are sensitive to ESD and should be handled with

appropriate measures.

2.3 System

Requirements

The system requirements are:

•

Personal Computer (PC) or unit compatible for RS232 communications.

•

An unused serial port (COM1…. COM4) for communication between the developer's board and the PC.

•

A second serial port may also be required for additional functionality.

•

A terminal program such as HyperTerminal, Kermit, Procomm, etc …

«
...
7
8
9
10
11
...
»

Содержание Developer's Board





























Отзывы:

Нет отзывов