Sony Ericsson Developer's Board Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

Sony Ericsson Developer's Board Скачать руководство пользователя страница 4

Developer's Board Manual Rev A

Page 4 of 28

SEM/CX-02:0061/MAN

1 Introduction

1.1 Overview

This manual is intended to familiarize the user with the developer's platform, demonstrate recommended HW
implementations for your applications and explain how to use the development platform in conjunction with your
application to accelerate your development.

The manual is broken into four chapters.

Chapter 1

presents an overview of the development platform, how to

get support and information to help you use the manual.

Chapter 2

discusses how to setup the developer's kit.

Chapter 3

describes the functionality of the developer's kit.

Chapter 4

is designed to show how the user can use

the developer's board to troubleshoot their application.

1.2 Service

and

Support

1.2.1 Web Page

For more information about where you can buy our modules or for recommendations of accessories and
components please visit our web-site:

http://www.sonyericsson.com/m2m

/

To register for product news and announcements or for product questions, contact the Sony Ericsson M2M
Technical Support group:

•

Telephone: (919) 472-1122 (Staffed Monday-Friday 9:00 AM - 5:00 PM EST).

•

E-mail:

[email protected]

1.3 Related

Documents

Document Title

Document Number

Rev

1

CM-42 Integrator's Manual

SEM/CX-02:0076/DES

A

CM-42 AT Command Manual

N/A

B

DM-15/25 Integrator's Manual

SEM/CX-02:0080/MAN

B

DM-15 AT Command Manual

N/A

A

DM-10/DM-20 Integrator's Manual

EUS/TB-01:0281/DES

E

1

The revision is the latest as of this manual release.

«
...
2
3
4
5
6
...
»

Содержание Developer's Board





























Отзывы:

Нет отзывов