Sonny's Pendulum 807W Combo Скачать руководство пользователя страница 4

Страница: 4 / 21

Owner

’s Manual

Pendulum 807W Combo

SonnysDirect.com

This document is confidential and proprietary to SONNY’S and cannot be used, disclosed or

Page 4 of 21

published without prior written consent. Content, prices, and availability subject to change without notice.

QUICK FIX - Pendulum 807W Combo.docx

– Rev 2021-A

13. Store all cleaning and washing solutions and oils in a well-ventilated area. Clean up fluid

spills immediately to prevent hazardous safety conditions. Be certain to follow all safety
procedures on SDS Sheets for each chemical product used.

14. All hydraulic and electric systems in the wash tunnel equipped with a torque relief or

overload should be checked and set at the minimum amount that will allow for proper
functionality under normal washing conditions.

15. No unauthorized people should ever be permitted in the wash tunnel or near the

equipment at any time.

* * *

! ! CAUTION ! !

When a piece of equipment must be in operation during inspection or maintenance, one
qualified technician must stay at the power disconnect switch while another qualified
technician performs the inspection or maintenance.

Содержание Pendulum 807W Combo






















Результаты поиска

Содержание Pendulum 807W Combo

Отзывы:

Похожие инструкции для Pendulum 807W Combo

Бренды по названию

Популярные бренды

Sonny's Pendulum 807W Combo, Руководство пользователя

Результаты поиска

Содержание Pendulum 807W Combo

Отзывы:

Похожие инструкции для Pendulum 807W Combo

Бренды по названию

Популярные бренды