SONIX SN32F107 Скачать руководство пользователя страница 13

Страница: 13 / 184

SN32F100 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 13

Version 1.9

PRODUCT OVERVIEW

1.1 FEATURES



Memory configuration



Timer

64KB on-chip Flash programming memory.

Two 16-bit and two 32-bit general purpose timers with

8KB SRAM.

a total of four capture inputs, 6PWMs

4KB Boot ROM



DAC



Operation Frequency up to 50MHz

16-bit Sigma-delta DAC for Audio.

Can drive the L/R Channel Earphone.



Interrupt sources

SNR 90dB.

ARM Cortex-M0 built-in Nested Vectored Interrupt

THD+N -75dB.

Controller (NVIC).



ADC



I/O pin configuration

16-bit Sigma-delta ADC for Audio.

Up to 62 General Purpose I/O (GPIO) pins with

AGC function.

Configurable pull-up/pull-down resistors.

Differential Microphone input.

GPIO pins can be used as edge and level sensitive

Build-in Microphone Bias Voltage support.

interrupt sources.

SNR 94dB.

High-current source driver (20 mA)

THD+N -80dB.

Comparator input pin: CM0~CM23.

Comparator output pin: CMO.



24-channel Comparator.



Programmable Watchdog Timer (WDT)

Programmable watchdog frequency with watchdog



Interface

Clock source and divider.

-Two I2C controllers supporting I2C-bus specification

with multiple address recognition and monitor mode.



System tick timer

-Two UART controllers with fractional baud rate

24-bit timer.

generation.

The system tick timer clock is fixed to the frequency of

-Two SPI controllers with SSP features and multi-

the system clock.

protocol capabilities.

The SysTick timer is intended to generate a fixed 10-ms

-I2S Function with mono and stereo audio data

interrupt.

supported, MSB justified data format supported, and

can operate as either master or slave.



Real-Time Clock (RTC)



System clocks



LVD with separate thresholds

-External high clock: Crystal type 10MHz~25MHz

Reset: 1.65V for V

CORE

1.8V, 2.0/2.4/2.7V for VDD

-External Audio high clock: Crystal type 16.384MHz

Interrupt: 2.0/2.4/2.7/3.0V for VDD

-External low clock: Crystal type 32.768 KHz

-Internal high clock: RC type 12 MHz



Fcpu (Instruction cycle)

-Internal low clock: RC type 16 KHz

CPU

= F

HCLK

= F

SYSCLK

/1, F

SYSCLK

/2, F

SYSCLK

/4, …,

-PLL allows CPU operation up to the maximum CPU

SYSCLK

/512.

rate without the need for a high-frequency crystal.

May be run from the external high clock or the



Working voltage 1.8V ~ 3.6V

internal high RC oscillator.

-Clock output function which can reflect the internal



Operating modes

high/low RC oscillator, HCLK, PLL output, and

Normal, Sleep, Deep-sleep, and Deep power-down

external high/low clock.



Serial Wire Debug (SWD)



Package (Chip form support)

LQFP 80 pin



In-System Programming (ISP) supported

LQFP 64 pin

LQFP 48 pin

Содержание SN32F107

























































































































































































Результаты поиска

Содержание SN32F107

Отзывы:

Похожие инструкции для SN32F107

Бренды по названию

Популярные бренды

SONIX SN32F107, Руководство пользователя

Результаты поиска

Содержание SN32F107

Отзывы:

Похожие инструкции для SN32F107

Бренды по названию

Популярные бренды