Sonifex SOVEREIGN MX-14S, Руководство пользователя, Страница: 22 / 65

<XR;X]T <^Sd[T ?PVT !$
C_fUbUYW^ EcUbc 7eYTU
Jumper Set Over Pins Effect
J9 1 & 2
None
Auto timer start.
No auto timer start.
J10 1 & 2
None
Remote stop is disabled.
Remote stop operates.
J11
1 & 2
None
Auto pre-fade cancelled by PFL button or fader open.
Auto pre-fade cancelled by PFL button only.
Note : Items in bold are set as default when shipped.
!"! DbX]V P ?WP]c^\ ?^fTaTS <XRa^_W^]T
If you are using a phantom powered microphone, jumper J1 must be set over pins 1
and 2. If a normal microphone is being used, then set the jumper over pins 2 and 3. With phantom
power selected, a voltage of +48V is applied to pins 2 and 3 of the XLR connector to power the
microphone, supplied through 6k8 resistors giving a current of 14mA. If a phantom powered
microphone is attached without setting the jumpers to 1 and 2, the microphone will not operate. When
using a phantom powered microphone, ensure that the mixer is switched off when the microphone is
plugged in to the XLR connector.
!"" 4]PQ[T ;5 ATb_^]bT ^] <XR 8]_dc
The LF ( bass ) response on the mic input can be configured so that it is less
responsive. Set J2 to have a full LF response or remove the jumper to have the LF roll-off. You may
require less LF response if, for example, the microphone being used is susceptible to low, rumbling
noises or the studio is acoustically poor ( such as large vehicles passing the station causing low
acoustic rumbles ).
!"# BT[TRc AT\^cT BcPacBc^_ U^a <XR ^a ;X]T
The mic or line inputs can be remotely started by use of the On button with the fader
up. The remote start is enabled by setting jumper J3 over pins 1 and 2 for the line input, or over pins 2
and 3 for the mic input. If J3 is not set, the remotes operate in either mic or line mode.
This can also be used if you have a Mic/Live display - the jumper should be set over
pins 2 and 3 and the start output used to control the display.
!"$ 4]PQ[T 2^]cX]d^db <^\T]cPah BcPac 5a^\ >] 1dcc^]
The On button can be made to remotely Start and Stop external equipment. If you
require each press of the On button to just send a Start signal, then set jumper J4. This might be useful
for a piece of external equipment which only has one remote input for starting and stopping.
If jumper J4 is not Set, each press of the On button will alternately send Start and
Stop signals.
!"% BcPac BT[TRc <^\T]cPah ^a ;PcRWTS
The remote start can be made either momentary or latched by setting the jumper J5
to 1 and 2 ( for momentary ) or 2 and 3 ( for latched ). If no jumper is set, the Start remote does not
operate.
!"& Bc^_ BT[TRc >] 5PSTa 3^f] ^a FXcW 1dcc^] D_
The input which is being remotely started can be remotely stopped as well. There
are two options available for stopping : To remotely stop when the fader is down, set the jumper J6
over pins 1 and 2. To remotely stop when the fader is down or the On button is pressed up, set J6 over
pins 2 and 3.