Caution: Risk of electric shock!
Do not attempt to disassemble or modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the assistance of
a specialist
.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance:
Do not cover!
Covering the unit can cause overheating, fire or electric shock!
FEATURES
fan heather for heating the air of indoor premises ● 4500 / max. 9000 W output ● operation modes: cold, warm, hot air ● built-in thermostat ● overheating and tipping over protection ● carrying
handle
FEATURES (figure 1.)
1. cold air inlet
2. warm air outlet
3. thermostat
4. carrying handle
5. operation mode switch
6. powerline connector
INSTALLATION
1. Before switching on for the first time, carefully remove the packaging material taking care not to damage the appliance and power cable. Do not use the product if it is damaged in any way!
2. The unit may only be used indoors in dry conditions!
3. Set the appliance on a stable and horizontal surface! The free flow of warm air must be ensured for proper operation, therefore, please note the minimum installation distances indicated in figure 2.
4. Verify that the appliance’s mode switch (5) is in OFF „0” position!
5. Only use standard 3P+N+E socket and power cable, with a minimum load of 400 V and 3 x 16 A.
6. Connect the appliance to a standard grounded 3P+N+E wall outlet! This makes the appliance ready for use.
OPERATION
You can select from the following modes by using the appliance’s operation mode switch (5):
0
fan and heating elements are switched off
„cold air”, only the fan is operating
„warm air”, the fan and the heater are switched on
„hot air”, the fan and both of the heating elements are switched on
When using the „cold air” the thermostat (3) has to be set to maximum
With the thermostat (3) you can set the room’s constant temperature. The appliance switches on at or operation mode, as soon as the air temperature drops below the set value. As soon as it
reaches the set temperature, the fan and the heating elements switch off. If you want higher temperature, turn the thermostat’s knob clockwise, if you want lower, then turn it to the opposite
direction.
If the thermostat is operating in the maximum value at or operation modes, and the fan is operating but the unit does not heat, then the overheating protection is activated. Turn the operation
mode switch to
„0”
position, then power off the appliance by unplugging the connector plug. Allow the appliance to cool (for at least 30 minutes). Check if the air inlet and outlet openings are free; if
necessary, clean them. Press the RESET button on the front of the appliance. Reinstall the appliance. If overheating protection activates again, power off the appliance by unplugging the
connector plug and consult a qualified service center.
CLEANING & MAINTENANCE
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of contamination.
1. Switch off and power off the unit by unplugging it from the electric outlet prior to cleaning!
2. Allow the appliance to cool (for at least 30 minutes).
3. Use a vacuum cleaner to clean the air inlet (1) and outlet (2) openings!
4. Use a slightly moistened cloth to clean the unit’s exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric components of the appliance.
TROUBLESHOOTING
Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste
equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of the product at a facility
specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local
waste management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs arising.
SPECIFICATIONS
power supply: . . . . . . . . . .
400
V
~
/ 50 Hz
output: . . . . . . . . . . . . . . .
4500
/
9000
W
IP protection: . . . . . . . . . . IPX4: Protected from splashing water (from all directions).
dimensions of heater: . . . . 5 10 x 350 x 370 mm
powerline connection: . . . . 3 P+N+E connector plug
lnoise level:. . . . . . . . . . . .
60
dB(A)
S
olution
Check the section on overheating protection.
Check the fan operation mode.
Check the settings of the operation mode switch.
Check the power supply.
Check the section on thermostat.
Set the thermostat to maximum.
Clean the appliance.
Malfunction
The appliance does not heat.
The appliance does not blow „cold air”.
Overheating protection activates frequently.
