SOMFY Animeo 1870452 Скачать руководство пользователя страница 52

Страница: 52 / 56

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

52/56

6.18.4.1

1-Bit value

Default value:



Selection options:



Off



Toggle



No function

•

If the “my” button in the radio transmitter is pressed, the object value “On” is generated. The duration of the
activity is not evaluated.

•

Off

If the “my” button in the radio transmitter is pressed, the object value “Off” is generated. The duration of the
activity is not evaluated.

•

Toggle

If the “my” button in the radio transmitter is pressed, the object value toggles between “On” and “Off”. The
duration of the activity is not evaluated.

•

No function

If the “my” button in the radio transmitter is pressed, no object is generated.

See chapter 1 Definitions

for On (“1”) Off (“0”) Toggle (“1/0”).

6.18.4.2

8-Bit value

Default value:



Selection options:



– 255

With this parameter the value (0

– 255) is set which is transmitted while pressing the “my” button in the radio

transmitter.

6.18.4.3

No function

If the “my” button in the radio transmitter is pressed, no object is generated.

Содержание Animeo 1870452
























































Результаты поиска

Содержание Animeo 1870452

Отзывы:

Бренды по названию

Популярные бренды

SOMFY Animeo 1870452, Руководство пользователя

Результаты поиска

Содержание Animeo 1870452

Отзывы:

Бренды по названию

Популярные бренды