SOMFY Animeo 1870452 Скачать руководство пользователя страница 40

Страница: 40 / 56

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

40/56

6.11

Menu index card “Bus safety”

On this menu index card, the reaction can be defined for every single motor output with bus power failure
and bus power return.

6.11.1

Motor 1…4

6.11.1.1

Reaction at bus power failure

Default value:



Ignore

Selection options:



Upper end limit



Lower end limit



Ignore



Intermediate position 1 (IP 1)



Intermediate position 2 (IP 2)



Close window



Open window

This parameter defines the position which is moved to with a bus power failure.

6.11.1.2

Reaction at bus power failure

Default value:



Ignore

Selection options:



Upper end limit



Lower end limit



Ignore



Intermediate position 1 (IP 1)



Intermediate position 2 (IP 2)



Close window



Open window

This parameter defines the position which is moved to with a bus power failure.

Содержание Animeo 1870452
























































Результаты поиска

Содержание Animeo 1870452

Отзывы:

Бренды по названию

Популярные бренды

SOMFY Animeo 1870452, Руководство пользователя

Результаты поиска

Содержание Animeo 1870452

Отзывы:

Бренды по названию

Популярные бренды