Solid State Logic Fusion страница 6 Скачать руководство пользователя

Страница: 6 / 35

Fusion User Guide

Introduction

Introduction

Fusion is an all-analogue stereo outboard processor created for the hybrid studio. Fusion introduces five completely new analogue
colouration tools designed to bring the perfect combination of added tonal character, clarity and depth to your mix bus or stereo
stems with the detail, warmth and finesse that only real analogue circuits can provide.

Features

➤

Five new SSL analogue colour circuits:

➤

VINTAGE DRIVE

- A unique non-linear saturation circuit designed to bring that cherished gradual analogue

overload sound you get from pushing vintage equipment into the sweet spot.

➤

VIOLET EQ

- a 2-band, minimum phase-shift shelving EQ offering instant low-end weight and glorious high-end

sheen. 4 fixed frequency points for each band with

9dB boost/cut.

➤

HF COMPRESSOR

- A high-frequency compressor, optimised for smooth taming of unwanted brittle sounds or

build-up of top-end fizz.

➤

STEREO IMAGE

- A built-in M/S circuit allows for sumptuous sculpting of the side-signal to allow for wider mixes

with added depth.

➤

TRANSFORMER CIRCUIT

- A custom SSL design that introduces subtle low-frequency harmonics for added

weight, alongside a touch of added transformer sparkle in the highs.

➤

Built-In Insert Point with two modes of operation:

➤

Stereo mode allows you to integrate additional outboard gear such as the SSL Bus Compressor. Switchable pre/
post the

VIOLET EQ

➤

Mid/Side mode allows you to insert two different mono outboard processors across the mid and side signals of the
mix. Switchable pre/post the

STEREO IMAGE

controls.

➤

3rd order

HPF

(High-Pass Filter) to clean up unwanted low-end.

➤

SuperAnalogue

±12dB centre-indented

INPUT

and

OUTPUT

trim controls to help achieve the best possible gain-staging

into and out of Fusion.

➤

Individual bypass switches for each circuit to compare sounds with/without each circuit.

➤

Master

BYPASS

switch with two modes of operation:

➤

Red mode: complete bypass.

➤

White mode: bypass that includes the

INPUT TRIM

control.

➤

Master meter, with 3-second peak hold segments. Switches from output to input metering upon pressing the

BYPASS

switch.

➤

Input clip

O/L

LEDs, triggered at +27dBu.

➤

Balanced XLR input and outputs throughout for easy and professional studio integration.

➤

Enhanced ‘dot-dash’ screening around controls to allow for easier and clearer recall.

➤

Adjustable front-panel meter and switch brightness to match the vibe of your studio environment.

Содержание Fusion




































Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды

Solid State Logic Fusion, Руководство пользователя

Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды